Test method

Related standards or drafts

Standards package "Conservation of Cultural Property – Test methods and tools for conservation works"

60.60 Standard published

Validation of environmental test methods

60.60 Standard published

CEN/Guides

Rheological test methods - Fundamentals and interlaboratory comparisons - Part 1: Determination of the yield point (ISO/TR 20659-1:2024)

60.60 Standard published

CEN/TC 139

Rheological test methods - Fundamentals and interlaboratory comparisons - Part 2: Determination of the time-dependent structural change (thixotropy) (ISO/TR 20659-2:2024)

60.60 Standard published

CEN/TC 139

Paints and varnishes - Overview of test methods on hardness and wear resistance of coatings (ISO/TR 21555:2019)

60.60 Standard published

CEN/TC 139

Cosmetics - Sun protection test methods - Review and evaluation of methods to assess the photoprotection of sun protection products (ISO/TR 26369:2009)

60.60 Standard published

CEN/TC 392

Paints and varnishes - Determination of volatile organic compound (VOC) and/or semi-volatile organic compound (SVOC) content - Best practices for the selection of test methods (ISO/TR 5601:2023)

60.60 Standard published

CEN/TC 139

Test method to measure the efficiency of air filtration media against spherical nanomaterials - Part 2: Size range from 3 nm to 30 nm (ISO/TS 21083-2:2019)

60.60 Standard published

CEN/TC 195

Jetting resistance of drain and sewer pipes - Moving jet test method

60.60 Standard published

CEN/TC 165

Petroleum products and other liquids - Applicability of test methods on sulfur determination in petrol and diesel fuel

60.60 Standard published

CEN/TC 19

Petroleum and related products - Applicability of diesel fuel test methods for Fatty Acid Methyl Esters (FAME) - Information and results on round robin tests

60.60 Standard published

CEN/TC 19

Welding of reinforcing steel - Tack weldability - Test methods and performance requirements

60.60 Standard published

CEN/TC 121

Hygrothermal performance of buildings - Resistance to wind - driven rain of roof coverings with discontinuously laid small elements - Test methods

60.60 Standard published

CEN/TC 89

Concrete - Release of regulated dangerous substances into soil, groundwater and surface water - Test method for new or unapproved constituents of concrete and for production concretes

60.60 Standard published

CEN/TC 51

Liquid petroleum products - Middle distillates and fatty acid methyl ester (FAME) fuels and blends - Round Robin report on applicability of Rapid Small Scale Oxidation Test method

60.60 Standard published

CEN/TC 19

Automotive fuels - Unleaded petrol containing more than 3,7 % (m/m) oxygen - Roadmap, test methods, and requirements for E10+ petrol

60.60 Standard published

CEN/TC 19

Liquid petroleum products - Investigation on test method for measurement of the oxidation stability of diesel and diesel/FAME blends by Acid Number after ageing

60.60 Standard published

CEN/TC 19

Ductile iron pipes, fittings and accessories - Sanitary characteristics and test methods

60.60 Standard published

CEN/TC 203

Validation testing program on chloride penetration and carbonation standardized test methods

60.60 Standard published

CEN/TC 104

Test methods for environmental characterization of solid matrices - Guide to flash point testing

60.60 Standard published

CEN/TC 444

Cycles - Components and assemblies used in bicycles - Innovative requirements and test methods

60.60 Standard published

CEN/TC 333

Test methods for external fire exposure to roofs

90.92 Standard to be revised

CEN/TC 127

Bituminous mixtures - Test methods - Part 50: Resistance to scuffing

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 51: Surface shear strength test

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 52: Conditioning to address oxidative ageing

90.92 Standard to be revised

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 2: Assessment of the skid resistance of a road pavement surface by the use of dynamic measuring systems

90.93 Standard confirmed

CEN/TC 227

Road restraint systems - Part 7: Performance characterisation and test methods for terminals of safety barriers

60.60 Standard published

CEN/TC 226

Road restraint systems - Part 9: Impact tests and test methods for removable barrier sections

60.60 Standard published

CEN/TC 226

Unbound and hydraulically bound mixtures - Part 54: Test method for the determination of frost susceptibility - Resistance to freezing and thawing of hydraulically bound mixtures

60.60 Standard published

CEN/TC 227

Wood-based panels - Floating floors - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 112

Materials and articles in contact with foodstuffs - Polymeric coatings on paper and board- Guide to the selection of conditions and test methods for overall migration

90.93 Standard confirmed

CEN/TC 194

Materials and articles in contact with foodstuffs - Polymeric coatings on metal substrates - Guide to the selection of conditions and test methods for overall migration

90.93 Standard confirmed

CEN/TC 194

Geosynthetic barriers - Test method for determining the resistance to roots

60.60 Standard published

CEN/TC 189

Geosynthetic barriers - Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers

60.60 Standard published

CEN/TC 189

Geosynthetic Barriers - Test method for the determination of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriers

60.60 Standard published

CEN/TC 189

Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 1:Guide to test method selection

90.93 Standard confirmed

CEN/TC 184

Materials and articles in contact with foodstuffs - Plastics - Polymeric additives - Test method for the determination of the mass fraction of a polymeric additive that lies below 1000 Daltons

90.93 Standard confirmed

CEN/TC 194

Curing compounds - Test methods - Part 1: Determination of water retention efficiency of common curing compounds

90.93 Standard confirmed

CEN/TC 104

Wood-based panels - Small scale indicative test methods for certain mechanical properties

90.93 Standard confirmed

CEN/TC 112

Durability of wood and wood-based products - Determination of the natural durability of solid wood against wood-destroying fungi, test methods - Part 2: Soft rotting micro-fungi

60.60 Standard published

CEN/TC 38

Protective clothing - Hand, arm, leg, genital and neck protectors for use in ice hockey - Protectors for players other than goalkeepers - Requirements and test methods

90.93 Standard confirmed

CEN/TC 162

Winter maintenance equipment - Road weather information systems - Part 4: Test methods for stationary equipment

60.60 Standard published

CEN/TC 337

Prefabricated timber stairs - Mechanical test methods

90.60 Close of review

CEN/TC 175

Residential solid fuel burning appliances - Emission test methods

90.93 Standard confirmed

CEN/TC 295

Chimney terminals - General requirements and material independent test methods

90.93 Standard confirmed

CEN/TC 166

Railway applications - Track - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 7: Extrinsic characteristics - In situ values of insertion loss

90.93 Standard confirmed

CEN/TC 256

Sandwich boards for furniture (SWB-F) - Factory made products - Definition, classification and test methods for determination of performance characteristics

90.93 Standard confirmed

CEN/TC 112

Waste - Test methods for the determination of the monolithic status of waste to be landfilled

90.93 Standard confirmed

CEN/TC 444

Winter service equipment and products - De-icing agents - Part 3: Other solid and liquid de-icing agents - Requirements and test methods

90.60 Close of review

CEN/TC 337

Requirements and test methods for electronic cigarette devices

90.93 Standard confirmed

CEN/TC 437

Textiles and textile products - Part 3: Safety of children's clothing - Security of attachment of metal mechanically applied press fasteners - Test method

90.60 Close of review

CEN/TC 248

Textiles and textile products - Part 4: Safety of children's clothing - Security of attachment of components except buttons and metal mechanically applied press fasteners - Test method

90.60 Close of review

CEN/TC 248

Child care articles - Tricycles - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

District heating pipes - Factory made flexible pipe systems - Classification, requirements and test methods for bonded or non-bonded system with thermoplastic reinforced service pipes (TRSP)

60.60 Standard published

CEN/TC 107

Non-destructive testing - Test method for determining residual stresses by synchrotron x-ray diffraction

60.60 Standard published

CEN/TC 138

Amendment 1 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-5: Uncertainties, statistics and limit modelling - Conditions for the use of alternative test methods

60.60 Standard published

CISPR/CIS/A

Amendment 2 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-5: Uncertainties, statistics and limit modelling - Conditions for the use of alternative test methods

60.60 Standard published

CISPR/CIS/A

Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-5: Uncertainties, statistics and limit modelling - Conditions for the use of alternative test methods

60.60 Standard published

CISPR/CIS/A

Test method on electromagnetic emissions - Part 1: Electronic control gear for single- and double-capped fluorescent lamps

60.60 Standard published

CISPR/CIS/F

Test method on electromagnetic emissions - Part 2: Electronic control gear for discharge lamps excluding fluorescent lamps

60.60 Standard published

CISPR/CIS/F

Electricity metering equipment (a.c.) - Severity levels, immunity requirements and test methods for conducted disturbances in the frequency range 2 kHz - 150 kHz

90.93 Standard confirmed

CLC/TC 13

External fire exposure to roofs in combination with photovoltaic (PV) arrays - Test method(s)

60.60 Standard published

CLC/TC 82

General guideline on real drive test methodology for compiling comparable emission data

90.93 Standard confirmed

CEN/WS 090

Lower-limb wearable devices - Performance test method for walking on uneven terrain

60.60 Standard published

CEN/WS 110

Test method for determination of the essential work of fracture of thin ductile metallic sheets

60.60 Standard published

CEN/WS FORMPLANET

Test method for the evaluation of the adhesive properties of fibre reinforced polymer composite joints

60.60 Standard published

CEN/WS 115

Real drive test method for collecting vehicle interior air quality data

60.60 Standard published

CEN/WS 103

Urban search and rescue - Guideline for the application of a test method for innovative technologies to detect victims in debris

60.60 Standard published

CEN/WS CURSOR

Test method for the determination of a cracking resistance index for advanced high strength steel sheets

60.60 Standard published

CEN/WS TOUGHSTEEL

Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods

90.60 Close of review

CEN/TC 128

Steel wire and wire products - General - Part 1: Test methods

90.60 Close of review

CEN/TC 459/SC 6

Office furniture - Screens - Part 3: Test methods

90.93 Standard confirmed

CEN/TC 207

Windows and doors - Air permeability - Test method

90.93 Standard confirmed

CEN/TC 33

Windows and doors - Water tightness - Test method

90.93 Standard confirmed

CEN/TC 33

Glass in building - Mirrors from silver-coated float glass for internal use - Part 1: Definitions, requirements and test methods

90.60 Close of review

CEN/TC 129

Metallic materials - Small punch test method

60.60 Standard published

CEN/TC 459/SC 1

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of basic bactericidal activity of chemical disinfectants and antiseptics - Test method and requirements (phase 1)

90.93 Standard confirmed

CEN/TC 216

Water slides - Part 1: Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Protective clothing against solid airborne particles including radioactive contamination - Part 1: Requirements and test methods for compressed air line ventilated protective clothing, protecting the body and the respiratory tract

90.93 Standard confirmed

CEN/TC 162

Protective clothing against radioactive contamination - Part 2: Requirements and test methods for non-ventilated protective clothing against particulate radioactive contamination

90.93 Standard confirmed

CEN/TC 162

Timber structures - Test methods - Joints made with punched metal plate fasteners

90.92 Standard to be revised

CEN/TC 124

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods

90.93 Standard confirmed

CEN/TC 114

Glass in building - Coated glass - Part 2: Requirements and test methods for class A, B and S coatings

90.60 Close of review

CEN/TC 129

Glass in building - Coated glass - Part 3: Requirements and test methods for class C and D coatings

90.60 Close of review

CEN/TC 129

Glass in building - Coated glass - Part 5 - Test method and classification for the self-cleaning performances of coated glass surfaces

90.60 Close of review

CEN/TC 129

Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements

60.60 Standard published

CEN/TC 155

Doors - Behaviour between two different climates - Test method

90.93 Standard confirmed

CEN/TC 33

Building hardware - Panic exit devices operated by a horizontal bar, for use on escape routes - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Furniture - Foldaway beds - Safety requirements and testing - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 207

Children's furniture - Cribs - Safety requirements and test methods

60.60 Standard published

CEN/TC 207

Children's furniture - Cribs - Safety requirements and test methods

60.60 Standard published

CEN/TC 207

Durability of wood and wood-based products - Test method against wood destroying basidiomycetes - Part 1: Assessment of biocidal efficacy of wood preservatives

60.60 Standard published

CEN/TC 38

Durability of wood and wood-based products - Test method against wood destroying basidiomycetes - Part 2: Assessment of inherent or enhanced durability

60.60 Standard published

CEN/TC 38

Durability of wood and wood-based products - Test method against wood destroying basidiomycetes - Part 3: Assessment of durability of wood-based panels

60.60 Standard published

CEN/TC 38

Protective clothing - Electrostatic properties - Part 1: Test method for measurement of surface resistivity

90.93 Standard confirmed

CEN/TC 162

Protective clothing - Electrostatic properties - Part 2: Test method for measurement of the electrical resistance through a material (vertical resistance)

90.93 Standard confirmed

CEN/TC 162

Protective clothing - Electrostatic properties - Part 3: Test methods for measurement of charge decay

90.60 Close of review

CEN/TC 162

Building hardware - Controlled door closing devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Buiding hardware - Controlled door closing devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Controlled door closing devices - Requirements and test methods

60.60 Standard published

CEN/TC 33

Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods

60.60 Standard published

CEN/TC 33

Building hardware - Door coordinator devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Door cordinator devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Door coordinator devices - Requirements and test methods

60.60 Standard published

CEN/TC 33

Feather and down - Test methods - Determination of moisture content

90.93 Standard confirmed

CEN/TC 222

Feather and down - Test methods - Determination of the oxygen index number

90.93 Standard confirmed

CEN/TC 222

Feather and down - Test methods - Determination of the oil and fat content

90.93 Standard confirmed

CEN/TC 222

Feather and down - Test methods - Determination of the turbidity of an aqueous extract

90.93 Standard confirmed

CEN/TC 222

Feather and down - Test methods - Determination of water-soluble chlorides

90.93 Standard confirmed

CEN/TC 222

Precast concrete products - Test methods for glassfibre reinforced concrete

60.60 Standard published

CEN/TC 229

Playground equipment and surfacing - Part 10: Additional specific safety requirements and test methods for fully enclosed play equipment

60.60 Standard published

CEN/TC 136

Playground equipment and surfacing - Part 11: Additional specific safety requirements and test methods for spatial network

90.93 Standard confirmed

CEN/TC 136

Playground equipment and surfacing - Part 1: General safety requirements and test methods

60.60 Standard published

CEN/TC 136

Playground equipment and surfacing - Part 2: Additional specific safety requirements and test methods for swings

90.93 Standard confirmed

CEN/TC 136

Playground equipment and surfacing - Part 3: Additional specific safety requirements and test methods for slides

90.93 Standard confirmed

CEN/TC 136

Playground equipment and surfacing - Part 4: Additional specific safety requirements and test methods for cableways

90.93 Standard confirmed

CEN/TC 136

Playground equipment and surfacing - Part 5: Additional specific safety requirements and test methods for carousels

60.60 Standard published

CEN/TC 136

Playground equipment and surfacing - Part 6: Additional specific safety requirements and test methods for rocking equipment

90.93 Standard confirmed

CEN/TC 136

Materials and articles in contact with foodstuffs - Test methods for thermal shock and thermal shock endurance

90.60 Close of review

CEN/TC 194

Materials and articles in contact with foodstuffs - Test methods for translucency of ceramic articles

90.60 Close of review

CEN/TC 194

Materials and articles in contact with foodstuffs - Plastics - Part 11: Test methods for overall migration into mixtures of C-labelled synthetic triglycerides

90.93 Standard confirmed

CEN/TC 194

Materials and articles in contact with foodstuffs - Plastics - Part 1: Guide to the selection of conditions and test methods for overall migration

90.93 Standard confirmed

CEN/TC 194

Materials and articles in contact with foodstuffs - Plastics - Part 13: Test methods for overall migration at high temperatures

60.60 Standard published

CEN/TC 194

Materials and articles in contact with foodstuffs - Plastics - Part 2: Test methods for overall migration in vegetable oils

60.60 Standard published

CEN/TC 194

Materials and articles in contact with foodstuffs - Plastics - Part 3: Test methods for overall migration in evaporable simulants

60.60 Standard published

CEN/TC 194

Windows and doors - Resistance to repeated opening and closing - Test method

90.93 Standard confirmed

CEN/TC 33

Timber structures - Test methods - Performance of structural floor decking

90.93 Standard confirmed

CEN/TC 112

Adhesives for ceramic tiles - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 67

Wood preservatives - Field test method for determining the relative protective effectiveness of a wood preservative exposed out of ground contact - Horizontal lap-joint method

60.60 Standard published

CEN/TC 38

Operating forces - Test method - Part 1: Windows

60.60 Standard published

CEN/TC 33

Operating forces - Test method - Part 2: Doors

90.93 Standard confirmed

CEN/TC 33

Building hardware - Door and window bolts - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Safety of industrial trucks - Test methods for measuring noise emissions

90.93 Standard confirmed

CEN/TC 150

Fixed firefighting systems - Components for gas extinguishing systems - Part 10: Requirements and test methods for pressure gauges and pressure switches

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 11: Requirements and test methods for mechanical weighing devices

90.93 Standard confirmed

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 12: Requirements and test methods for pneumatic alarm devices

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 13: Requirements and test methods for check valves and non-return valves

90.93 Standard confirmed

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 13: Requirements and test methods for check valves and non-return valves

60.60 Standard published

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 16: Requirements and test methods for odorizing devices for CO2 low pressure systems

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 2: Requirements and test methods for non-electrical automatic control and delay devices

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 3: Requirements and test methods for manual triggering and stop devices

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 4: Requirements and test methods for container valve assemblies and their actuators

90.93 Standard confirmed

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 5: Requirements and test methods for high and low pressure selector valves and their actuators

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 6: Requirements and test methods for non-electrical disable devices

90.60 Close of review

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 7: Requirements and test methods for nozzles for CO2 systems

90.92 Standard to be revised

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 7: Requirements and test methods for nozzles for CO2 systems

60.60 Standard published

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 8: Requirements and test methods for connectors

90.93 Standard confirmed

CEN/TC 191

Fixed firefighting systems - Components for gas extinguishing systems - Part 9: Requirements and test methods for special fire detectors

90.60 Close of review

CEN/TC 191

Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength

90.60 Close of review

CEN/TC 155

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports

90.93 Standard confirmed

CEN/TC 155

Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off

90.92 Standard to be revised

CEN/TC 155

Thermal performance of buildings - Air permeability of building components and building elements - Laboratory test method

90.92 Standard to be revised

CEN/TC 89

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling

90.93 Standard confirmed

CEN/TC 155

Feather and down - Test methods - Determination of the fill power (massic volume)

90.93 Standard confirmed

CEN/TC 443

Feather and down - Test methods - Determination of the quantitative composition of feather and down (manual method)

90.92 Standard to be revised

CEN/TC 443

Curtain walling - Air permeability - Test method

60.60 Standard published

CEN/TC 33

Materials and articles in contact with foodstuffs - Test methods for water absorption of ceramic articles

90.60 Close of review

CEN/TC 194

Curtain walling - Resistance to wind load - Test method

90.93 Standard confirmed

CEN/TC 33

Manual wheelchairs - Requirements and test methods

60.60 Standard published

CEN/TC 293

Electrically powered wheelchairs, scooters and their chargers - Requirements and test methods

60.60 Standard published

CEN/TC 293

Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion steel-to-steel for characterisation of structural bonding agents

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of open time

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of compressive strength of repair mortar

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 1: Test method for dry components of premixed mortar

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 2: Test method for fillers for polymer bonding agents

90.93 Standard confirmed

CEN/TC 104

Shutters, external and internal blinds - Misuse - Test methods

90.93 Standard confirmed

CEN/TC 33

Gymnastic equipment - Horses and bucks - Functional and safety requirements, test methods

60.60 Standard published

CEN/TC 136

Gymnastic equipment - Horizontal bars - Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Building hardware - Mechanically operated locks and locking plates - Characteristics and test methods

60.60 Standard published

CEN/TC 33

Windows and doors - Resistance to wind load - Test method

90.93 Standard confirmed

CEN/TC 33

Child use and care articles - Changing units for domestic use - Part 2: Test methods

90.92 Standard to be revised

CEN/TC 252

Playpens for domestic use - Safety requirements and test methods

90.60 Close of review

CEN/TC 207

Surfaces for sports areas - Test method for the determination of tensile properties of synthetic sports surfaces

60.60 Standard published

CEN/TC 217

Mountaineering equipment - Chocks - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Surface dressing - Test methods - Part 1: Rate of spread and accuracy of spread of binder and chippings

90.93 Standard confirmed

CEN/TC 227

Surface dressing - Test methods - Part 2: Visual assessment of defects

90.93 Standard confirmed

CEN/TC 227

Surface dressing - Test methods - Part 3: Determination of binder aggregate adhesivity by the Vialit plate shock test method

90.92 Standard to be revised

CEN/TC 227

Slurry surfacing - Test methods - Part 1: Sampling of slurry surfacing mixture

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 2: Determination of residual binder content including preparation of samples

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 3: Consistency

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 4: Determination of cohesion of the mix

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test method - Part 5: Determination of the minimum binder content and wearing resistance

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 6: Rate of application

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 7: Shaking abrasion test

90.93 Standard confirmed

CEN/TC 227

Slurry surfacing - Test methods - Part 8: Visual assessment of defects

90.93 Standard confirmed

CEN/TC 227

Mountaineering equipment - Connectors - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Mountaineering equipment - Frictional anchors - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Mountaineering equipment - Harnesses - Safety requirements and test methods

90.92 Standard to be revised

CEN/TC 136

Montaineering equipment - Pulleys - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure

90.93 Standard confirmed

CEN/TC 155

Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 3: Requirements, test conditions and test methods

60.60 Standard published

CEN/TC 299

Building hardware - Padlocks and padlock fittings - Requirements and test methods

60.60 Standard published

CEN/TC 33

Gymnastic equipment - Wall bars, lattice ladders and climbing frames - Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 3: Deflection recovery test method

90.93 Standard confirmed

CEN/TC 33

Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 4: Recovery after accelerated ageing test method

90.93 Standard confirmed

CEN/TC 33

Natural stone test methods - Determination of resistance to salt crystallisation

60.60 Standard published

CEN/TC 246

Natural stone test methods - Determination of frost resistance

90.60 Close of review

CEN/TC 246

Natural stone test methods - Determination of flexural strength under concentrated load

60.60 Standard published

CEN/TC 246

Packaging - Flexible tubes - Test method for the air tightness of closures

60.60 Standard published

CEN/TC 261

Natural stone test methods - Petrographic examination

90.60 Close of review

CEN/TC 246

Gully tops and manhole tops for vehicular and pedestrian areas - Part 1: Definitions, classification, general principles of design, performance requirements and test methods

90.93 Standard confirmed

CEN/TC 165

Vehicle parking control equipment - Requirements and test methods for a parking terminal

60.60 Standard published

CEN/TC 226

Fixed firefighting systems - Powder systems - Part 1: Requirements and test methods for components

60.60 Standard published

CEN/TC 191

Industrial, commercial and garage doors and gates - Air permeability - Test method

90.92 Standard to be revised

CEN/TC 33

Gymnastic equipment - Balancing beams - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Geotextiles and geotextile-related products - Screening test method for determining the resistance to hydrolysis in water

60.60 Standard published

CEN/TC 189

Industrial, commercial and garage doors and gates - Safety in use of power operated doors - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Fibre-cement flat sheets - Product specification and test methods

90.92 Standard to be revised

CEN/TC 128

Chemicals used for treatment of water intended for human consumption - Calcium carbonate, high-calcium lime, half-burnt dolomite, magnesium oxide, calcium magnesium carbonate and dolomitic lime - Test methods

60.60 Standard published

CEN/TC 164

Industrial, commercial and garage doors and gates - Resistance to water penetration - Test method

90.92 Standard to be revised

CEN/TC 33

Paragliding equipment - Emergency parachutes - Safety requirements and test methods

60.60 Standard published

CEN/TC 136

Mountaineering equipment - Helmets for mountaineers - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 158

Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners

90.92 Standard to be revised

CEN/TC 124

Timber Structures - Test methods - Cyclic testing of joints made with mechanical fasteners

60.60 Standard published

CEN/TC 124

Castors and wheels - Test methods and apparatus

90.93 Standard confirmed

CEN/TC 324

Copper and copper alloys - Plumbing fittings - Part 20: Definitions, thread dimensions, test methods, reference data and supporting information

60.60 Standard published

CEN/TC 133

Textiles - Para-aramid multifilament yarns - Test methods

90.93 Standard confirmed

CEN/TC 248

Artificial climbing structures - Part 1: Safety requirements and test methods for ACS with protection points

90.92 Standard to be revised

CEN/TC 136

Artificial climbing structures - Part 2: Safety requirements and test methods for bouldering walls

90.92 Standard to be revised

CEN/TC 136

Artificial climbing structures - Part 3: Safety requirements and test methods for climbing holds

90.92 Standard to be revised

CEN/TC 136

Stationary waste containers - Part 2: Performance requirements and test methods

90.93 Standard confirmed

CEN/TC 183

Child use and care articles - Soother holder - Safety requirements and test methods

90.92 Standard to be revised

CEN/TC 252

Glass in building - Pendulum test - Impact test method and classification for flat glass

90.60 Close of review

CEN/TC 129

Industrial, commercial and garage doors and gates - Mechanical aspects - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces

90.93 Standard confirmed

CEN/TC 249

Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 2: PVC-U profiles covered with foils bonded with adhesives

60.60 Standard published

CEN/TC 249

Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 4: PVC-U profiles with thermo-laminated foils

60.60 Standard published

CEN/TC 249

Products and systems for the protection and repair of concrete structures - Test methods - Determination of glass transition temperatures of polymers

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of slant shear strength

90.93 Standard confirmed

CEN/TC 104

Surfaces for sports areas - Test methods for the determination of vertical water infiltration and horizontal water flow rates

60.60 Standard published

CEN/TC 217

Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Determination of linear shrinkage for polymers and surface protection systems (SPS)

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Shrinkage of crack injection products based on polymer binder: volumetric shrinkage

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of early age linear shrinkage for structural bonding agents

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 4: Determination of shrinkage and expansion

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Adhesion and elongation capacity of injection products with limited ductility

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Determination of the adhesion of injection products, with our without thermal cycling - Adhesion by tensile bond strength

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of the adhesion of injection products, with or without thermal cycling - Slant shear method

90.93 Standard confirmed

CEN/TC 104

Diving accessories - Combined buoyancy and rescue devices - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Diving accessories - Combined buoyancy and rescue devices - Functional and safety requirements, test methods

60.60 Standard published

CEN/TC 136

Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods

90.93 Standard confirmed

CEN/TC 53

Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Part 1: Compatibility with concrete

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Part 3: Effect of injection products on elastomers

90.93 Standard confirmed

CEN/TC 104

Gymnastic equipment - Hanging rings - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Roll containers - Part 3: Test methods

90.93 Standard confirmed

CEN/TC 261

Roll containers - Part 3: Test methods

60.60 Standard published

CEN/TC 261

Anti-glare systems for roads - Part 2: Test methods

90.60 Close of review

CEN/TC 226

Bituminous mixtures - Test methods - Part 10: Compactability

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 11: Determination of the affinity between aggregate and bitumen

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 1: Soluble binder content

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 12: Determination of the water sensitivity of bituminous specimens

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 13: Temperature measurement

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 14: Water content

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 15: Determination of the segregation sensitivity

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 16: Abrasion by studded tyres

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 17: Particle loss of porous asphalt specimens

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 18: Binder drainage

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 19: Permeability of specimen

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 20: Indentation using cube or Marshall specimens

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 21: Indentation using plate specimens

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 22: Wheel tracking

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 23: Determination of the indirect tensile strength of bituminous specimens

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 24: Resistance to fatigue

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 25: Cyclic compression test

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 26: Stiffness

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 26: Stiffness

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 27: Sampling

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 28: Preparation of samples for determining binder content, water content and grading

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 29: Determination of the dimensions of a bituminous specimen

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 30: Specimen preparation by impact compactor

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 31: Specimen preparation by gyratory compactor

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 3: Bitumen recovery: Rotary evaporator

90.93 Standard confirmed

CEN/TC 227

Bituminous mixtures - Test methods - Part 32: Specimen preparation by vibratory compactor

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test method - Part 33: Specimen prepared by roller compactor

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 34: Marshall test

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 35: Laboratory mixing

90.92 Standard to be revised

CEN/TC 227

Bituminous mixtures - Test methods - Part 36: Determination of the thickness of bituminous pavement

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for Hot-Rolled-Asphalt (HRA)

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods for hot mix asphalt - Part 38: Common equipment and calibration

90.93 Standard confirmed

CEN/TC 227

Bituminous mixtures - Test methods - Part 39: Binder content by ignition

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 40: In situ drainability

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 41: Resistance to de-icing fluids

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 4: Bitumen recovery: Fractionating column

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 42: Amount of foreign matter in reclaimed asphalt

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 43: Resistance to fuel

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 44: Crack propagation by semi-circular bending test

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 45: Saturation Ageing Tensile Stiffness (SATS) conditioning test

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 46: Low temperature cracking and properties by uniaxial tension tests

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 47: Determination of the ash content of natural asphalts

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 48: Interlayer Bonding

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 49: Determination of friction after polishing

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 5: Determination of the maximum density

90.60 Close of review

CEN/TC 227

Bituminous mixtures - Test methods - Part 53: Cohesion increase by spreadability-meter method

90.20 Standard under periodical review

CEN/TC 227

Bituminous mixtures - Test methods - Part 54: Curing of specimen for test of mixtures with bitumen emulsion

90.20 Standard under periodical review

CEN/TC 227

Bituminous mixtures - Test methods - Part 55: Organoleptic assessment of mixtures with bitumen emulsion

90.20 Standard under periodical review

CEN/TC 227

Bituminous mixtures - Test methods - Part 56: Specimen preparation by static compaction

90.20 Standard under periodical review

CEN/TC 227

Bituminous mixtures - Test methods - Part 6: Determination of bulk density of bituminous specimens

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 7: Determination of the bulk density of bituminous specimens by gamma rays

60.60 Standard published

CEN/TC 227

Bituminous mixtures - Test methods - Part 8: Determination of void characteristics of bituminous specimens

90.60 Close of review

CEN/TC 227

Playing field equipment - Basketball equipment - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Adhesives - Test methods for hydraulic setting floor smoothing and/or levelling compounds - Determination of flow characteristics

90.60 Close of review

CEN/TC 193

Playing field equipment - Volleyball equipment - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Child care articles - Table mounted chairs - Safety requirements and test methods

90.60 Close of review

CEN/TC 252

Child care articles - Baby walking frames - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Footwear - Test methods for outsoles - Compression energy

90.60 Close of review

CEN/TC 309

Footwear - Test methods for outsoles - Compression energy

60.60 Standard published

CEN/TC 309

Footwear - Test methods for insoles - Delamination resistance

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for insoles - Heel pin holding strength

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for insoles - Abrasion resistance

90.60 Close of review

CEN/TC 309

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of basic fungicidal or basic yeasticidal activity of chemical disinfectants and antiseptics - Test method and requirements (phase 1)

90.93 Standard confirmed

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and antiseptics used in food, industrial, domestic and institutional areas - Test method and requirements (phase 2, step 1)

90.20 Standard under periodical review

CEN/TC 216

Passive safety of support structures for road equipment - Requirements and test methods

60.60 Standard published

CEN/TC 226

Footwear - Test methods for outsoles - Abrasion resistance

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for outsoles - Tear strength

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for outsoles - Dimensional stability

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for outsoles - Needle tear strength

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for outsoles - Determination of split tear strength and delamination resistance

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for insoles - Resistance to stitch tear

90.93 Standard confirmed

CEN/TC 309

Footwear - Test methods for whole shoe - Heel attachment

90.93 Standard confirmed

CEN/TC 309

Chemical disinfectants and antiseptics - Surgical hand disinfection - Test method and requirements (phase 2, step 2)

90.93 Standard confirmed

CEN/TC 216

Glass in building - Insulating glass units - Part 2: Long term test method and requirements for moisture penetration

90.60 Close of review

CEN/TC 129

Glass in building - Insulating glass units - Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances

90.60 Close of review

CEN/TC 129

Footwear - Test methods for insoles - Dimensional stability

90.60 Close of review

CEN/TC 309

Footwear - Test methods for insoles, lining and insocks - Perspiration resistance

90.60 Close of review

CEN/TC 309

Footwear - Test methods for insoles, lining and insocks - Perspiration resistance

60.60 Standard published

CEN/TC 309

Footwear - Test methods for outsoles - Tensile strength and elongation

90.60 Close of review

CEN/TC 309

Footwear - Test methods for outsoles - Tensile strength and elongation

60.60 Standard published

CEN/TC 309

Skylight and conservatory roller shutters - Resistance to snow load - Test method

90.93 Standard confirmed

CEN/TC 33

Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods

90.60 Close of review

CEN/TC 203

Gypsum blocks - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Gypsum based adhesives for gypsum blocks - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Gypsum based adhesives for gypsum blocks - Definitions, requirements and test methods

60.60 Standard published

CEN/TC 241

Influence of materials on water intended for human consumption - Influence due to migration - Part 1: Test method for factory-made products made from or incorporating organic or glassy (porcelain/vitreous enamel) materials

90.93 Standard confirmed

CEN/TC 164

Influence of materials on water intended for human consumption - Influence due to migration - Part 2: Test method for non-metallic and noncementitious site-applied materials

60.60 Standard published

CEN/TC 164

Influence of materials on water intended for human consumption - Influence due to migration - Part 3: Test method for ion exchange and adsorbent resins

90.60 Close of review

CEN/TC 164

Influence of materials on water intended for human consumption - Influence due to migration - Part 4: Test method for water treatment membranes

60.60 Standard published

CEN/TC 164

Mechanical dishwashing resistance of utensils - Part 1: Reference test method for domestic articles

90.92 Standard to be revised

CEN/TC 194

Prefabricated accessories for roofing - Permanently fixed roof ladders - Product specification and test methods

90.60 Close of review

CEN/TC 128

Footwear - Test methods for shanks - Longitudinal stiffness

90.93 Standard confirmed

CEN/TC 309

Mastic asphalt for waterproofing - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 314

Reinforcements - Specification for textile glass chopped strands - Part 2: Test methods and general requirements

90.93 Standard confirmed

CEN/TC 249

Thermal solar systems and components - Factory made systems - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 312

Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems

90.93 Standard confirmed

CEN/TC 312

Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores

90.93 Standard confirmed

CEN/TC 312

Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores

90.93 Standard confirmed

CEN/TC 312

Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment

90.93 Standard confirmed

CEN/TC 312

Industrial, commercial and garage doors and gates and pedestrian doorsets - Protective devices for power operated doors and gates - Requirements and test methods

60.60 Standard published

CEN/TC 33

Building hardware - Cylinders for locks - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Road and airfield surface characteristics - Test methods - Part 1: Measurement of pavement surface macrotexture depth using a volumetric patch technique

90.93 Standard confirmed

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 3: Measurement of pavement surface horizontal drainability

90.93 Standard confirmed

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test

90.92 Standard to be revised

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 5: Determination of longitudinal unevenness indices

90.20 Standard under periodical review

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 6: Measurement of transverse and longitudinal profiles in the evenness and megatexture wavelength ranges

90.93 Standard confirmed

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 7: Irregularity measurement of pavement courses : the straightedge test

90.93 Standard confirmed

CEN/TC 227

Road and airfield surface characteristics - Test methods - Part 8: Determination of transverse unevenness indices

90.92 Standard to be revised

CEN/TC 227

Windows and doors - Soft and heavy body impact - Test method, safety requirements and classification

60.60 Standard published

CEN/TC 33

Influence of materials on water intended for human consumption - Organic materials - Determination of colour and turbidity of water in piping systems - Part 1: Test method

90.93 Standard confirmed

CEN/TC 164

Packaging - Complete, filled transport packages - Test methods for the determination of the centre of gravity of a package

90.93 Standard confirmed

CEN/TC 261

Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance of capillary absorption

90.93 Standard confirmed

CEN/TC 104

Safety of industrial trucks - Test methods for measuring vibration

90.93 Standard confirmed

CEN/TC 150

Protective clothing - Shin guards for association football players - Requirements and test methods

90.60 Close of review

CEN/TC 162

Products and systems for the protection and repair of concrete structure - Test method - Determination of thixotropy of products for protection of reinforcement

90.93 Standard confirmed

CEN/TC 104

Chimneys - System chimneys with clay/ceramic flue liners - Part 1: Requirements and test methods for sootfire resistance

90.93 Standard confirmed

CEN/TC 166

Chimneys - System chimneys with clay/ceramic flue liners - Part 2: Requirements and test methods under wet conditions

90.93 Standard confirmed

CEN/TC 166

Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys

90.93 Standard confirmed

CEN/TC 166

Chimneys - Clay/ceramic outer walls for system chimneys - Requirements and test methods

90.93 Standard confirmed

CEN/TC 166

Footwear - Test methods for whole shoe - Water resistance

90.60 Close of review

CEN/TC 309

Agricultural machinery - Manure spreaders - Environmental protection - Requirements and test methods

90.93 Standard confirmed

CEN/TC 144

Protective helmets - Test methods - Part 10: Resistance to radiant heat

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 1: Conditions and conditioning

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 1: Conditions and conditioning

60.60 Standard published

CEN/TC 158

Protective helmets - Test methods - Part 2: Shock absorption

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 3: Resistance to penetration

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 3: Resistance to penetration

60.60 Standard published

CEN/TC 158

Protective helmets - Test methods - Part 4: Retention system effectiveness

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 5: Retention system strength

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 6: Field of vision

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 7: Flame resistance

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 7: Flame resistance

60.60 Standard published

CEN/TC 158

Protective helmets - Test methods - Part 8: Electrical properties

90.93 Standard confirmed

CEN/TC 158

Protective helmets - Test methods - Part 8: Electrical properties

60.60 Standard published

CEN/TC 158

Mountaineering equipment - Ice-tools - Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Mountaineering equipment - Ice-tools - Safety requirements and test methods

60.60 Standard published

CEN/TC 136

Windows, doors and shutters - Explosion resistance - Test method - Part 1: Shock tube

90.93 Standard confirmed

CEN/TC 33

Windows, doors and shutters - Explosion resistance - Test method - Part 2: Range test

90.92 Standard to be revised

CEN/TC 33

Building hardware - Requirements and test methods for windows and doors height windows - Part 10: Arm-balancing systems

90.93 Standard confirmed

CEN/TC 33

Building hardware - Requirements and test methods for windows and doors height windows - Part 11: Top hung projecting reversible hardware

90.93 Standard confirmed

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware

60.60 Standard published

CEN/TC 33

Building hardware - Requirements and test methods for windows and doors height windows - Part 12: Side hung projecting reversible hardware

90.93 Standard confirmed

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 13: Sash balances

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 14: Sash fasteners

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 15: Rollers for horizontal sliding and hardware for sliding folding windows

90.60 Close of review

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows

90.60 Close of review

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 17: Hardware for Tilt and Slide windows

90.60 Close of review

CEN/TC 33

Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices

90.93 Standard confirmed

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 2: Window fastener handles

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door-height windows - Requirements and test methods - Part 3: Handles, primarily for Tilt and Turn, Tilt-First and Turn-Only hardware

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 4: Espagnolettes

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 5: Devices that restrict the opening of windows and door height windows

90.93 Standard confirmed

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)

90.93 Standard confirmed

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 7: Finger catches

60.60 Standard published

CEN/TC 33

Building hardware - Hardware for windows and door height windows - Part 8: Requirements and test methods for Tilt and Turn, Tilt-First and Turn-Only hardware

90.93 Standard confirmed

CEN/TC 33

Building hardware - Requirements and test methods for windows and door height windows - Part 9: Hardware for horizontal and vertical pivot windows

90.93 Standard confirmed

CEN/TC 33

Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 1: Guide to test methods for the specific migration of substances from plastics to foods and food simulants and the determination of substances in plastics and the selection of conditions of exposure to food simulants

90.92 Standard to be revised

CEN/TC 194

Buoyant aids for swimming instruction - Part 1: Safety requirements and test methods for buoyant aids to be worn

60.60 Standard published

CEN/TC 162

Buoyant aids for swimming instruction - Part 1: Safety requirements and test methods for buoyant aids to be worn

60.60 Standard published

CEN/TC 162

Buoyant aids for swimming instruction - Part 2: Safety requirements and test methods for buoyant aids to be held

60.60 Standard published

CEN/TC 162

Buoyant aids for swimming instruction - Part 3: Safety requirements and test methods for swim seats into which a user is positioned

60.60 Standard published

CEN/TC 162

Railway applications - Track - Test methods for fastening systems - Part 10: Proof load test for pull-out resistance

90.93 Standard confirmed

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint

90.93 Standard confirmed

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 2: Determination of torsional resistance

90.93 Standard confirmed

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 3: Determination of attenuation of impact loads

90.93 Standard confirmed

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 4: Effect of repeated loading

60.60 Standard published

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 5: Determination of electrical resistance

90.60 Close of review

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 5: Determination of electrical resistance

60.60 Standard published

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 6: Effect of severe environmental conditions

90.60 Close of review

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 7: Determination of clamping force and uplift stiffness

90.93 Standard confirmed

CEN/TC 256

Railway applications - Track - Test methods for fastening systems - Part 9: Determination of stiffness

60.60 Standard published

CEN/TC 256

Workbenches for laboratories in educational institutions - Dimensions, safety and durability requirements and test methods

60.60 Standard published

CEN/TC 207

Protective clothing - Protective jackets, body and shoulder protectors for equestrian use, for horse riders and those working with horses, and for horse drivers - Requirements and test methods

90.60 Close of review

CEN/TC 162

Natural stone test methods - Determination of flexural strength under constant moment

90.60 Close of review

CEN/TC 246

Road restraint systems - Part 1: Terminology and general criteria for test methods

60.60 Standard published

CEN/TC 226

Road restraint systems - Part 2: Performance classes, impact test acceptance criteria and test methods for safety barriers including vehicle parapets

60.60 Standard published

CEN/TC 226

Road restraint systems - Part 3: Performance classes, impact test acceptance criteria and test methods for crash cushions

60.60 Standard published

CEN/TC 226

Packaging - Small Load Carrier Systems - Part 1: Common requirements and test methods

90.60 Close of review

CEN/TC 261

Child care articles - Child carriers - Safety requirements and test methods - Part 1: Framed back carrier

60.60 Standard published

CEN/TC 252

Child use and care articles - Baby carriers - Safety requirements and test methods - Part 2: Soft carrier

90.92 Standard to be revised

CEN/TC 252

Child care articles - Part 1: Children's harnesses, reins - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Child care articles - Part 2: Children's harnesses incorporating backpacks and reins - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Chimneys - Test methods for system chimneys - Part 1: General test methods

90.60 Close of review

CEN/TC 166

Gymnastic equipment - Trampolines - Functional and safety requirements, test methods

90.60 Close of review

CEN/TC 136

Cookware - Coffee makers for domestic use with an independent heat source - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 194

Materials and articles in contact with foodstuffs - Test methods for crazing resistance of ceramic articles

90.93 Standard confirmed

CEN/TC 194

Protective equipment for martial arts - Part 1: General requirements and test methods

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 2: Additional requirements and test methods for instep protectors, shin protectors and forearm protectors

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 3: Additional requirements and test methods for trunk protectors

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 4: Additional requirements and test methods for head protectors

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 4: Additional requirements and test methods for head protectors

60.60 Standard published

CEN/TC 162

Protective equipment for martial arts - Part 5: Additional requirements and test methods for genital protectors and abdominal protectors

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 6: Additional requirements and test methods for breast protectors for females

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 7: Additional requirements and test methods for hand and foot protectors

90.60 Close of review

CEN/TC 162

Protective equipment for martial arts - Part 8: Additional requirements and test methods for karate face protectors

90.60 Close of review

CEN/TC 162

Gypsum binders and gypsum plasters - Part 2: Test methods

90.60 Close of review

CEN/TC 241

Unbound and hydraulically bound mixtures - Part 1: Test methods for laboratory reference density and water content - Introduction, general requirements and sampling

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 2: Test methods for laboratory reference density and water content - Proctor compaction

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 2: Test methods for laboratory reference density and water content - Proctor compaction

60.60 Standard published

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 3: Test methods for laboratory reference density and water content - Vibrocompression with controlled parameters

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 40: Test method for the determination of the direct tensile strength of hydraulically bound mixtures

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 41: Test method for the determination of the compressive strength of hydraulically bound mixtures

60.60 Standard published

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 4: Test methods for laboratory reference density and water content - Vibrating hammer

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 42: Test method for the determination of the indirect tensile strength of hydraulically bound mixtures

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 43: Test method for the determination of the modulus of elasticity of hydraulically bound mixtures

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 44: Test method for the determination of the alpha coefficient of vitrified blast furnace slag

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 45: Test method for the determination of the workability period of hydraulically bound mixtures

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 46: Test method for the determination of the moisture condition value

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 47: Test method for the determination of California bearing ratio, immediate bearing index and linear swelling

60.60 Standard published

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 48: Test method for the determination of degree of pulverisation

90.93 Standard confirmed

CEN/TC 227

Unbound and hydraulically bound mixtures - Part 5: Test methods for laboratory reference density and water content - Vibrating table

90.93 Standard confirmed

CEN/TC 227

Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation

90.92 Standard to be revised

CEN/TC 104

Kitchen sinks - Functional requirements and test methods

90.93 Standard confirmed

CEN/TC 163

Diving accessories - Depth gauges and combined depth and time measuring devices - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Laminate floor coverings - Specifications, requirements and test methods

60.60 Standard published

CEN/TC 134

Shutters - Hard body impact and prevention of access - Test methods

90.93 Standard confirmed

CEN/TC 33

Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods

90.93 Standard confirmed

CEN/TC 249

Solid wood panels (SWP) - Bonding quality - Test method

90.60 Close of review

CEN/TC 112

Natural stone test methods - Determination of the breaking load at dowel hole

90.92 Standard to be revised

CEN/TC 246

Natural stone test methods - Determination of geometric characteristics on units

60.60 Standard published

CEN/TC 246

Temporary edge protection systems - Product specification - Test methods

90.93 Standard confirmed

CEN/TC 53

Test methods for determining the contribution to the fire resistance of structural members - Part 10: Applied protection to solid steel bars in tension

60.60 Standard published

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 1: Horizontal protective membranes

60.60 Standard published

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 2: Vertical protective membranes

90.60 Close of review

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 3: Applied protection to concrete members

90.92 Standard to be revised

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 4: Applied passive protection to steel members

90.92 Standard to be revised

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 5: Applied protection to concrete/profiled sheet steel composite member

90.93 Standard confirmed

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 6: Applied protection to concrete filled hollow steel columns

90.93 Standard confirmed

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 7: Applied protection to timber members

60.60 Standard published

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 8: Applied reactive protection to steel members

90.92 Standard to be revised

CEN/TC 127

Test methods for determining the contribution to the fire resistance of structural members - Part 9: Applied fire protection systems to steel beams with web openings

90.93 Standard confirmed

CEN/TC 127

Concrete paving blocks - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Concrete paving blocks - Requirements and test methods

60.60 Standard published

CEN/TC 178

Armourstone, Part 2: Test methods

90.60 Close of review

CEN/TC 154

Concrete paving flags - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Concrete paving flags - Requirements and test methods

60.60 Standard published

CEN/TC 178

Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 1: Test for flow of thixotropic mortars

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 2: Test for flow of grout or mortar

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 3: Test for flow of repair concrete

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 4: Application of repair mortar overhead

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Measurement of chloride ion ingress

90.93 Standard confirmed

CEN/TC 104

Concrete kerb units - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Concrete kerb units - Requirements and test methods

60.60 Standard published

CEN/TC 178

Agricultural machinery - Slurry tankers and spreading devices - Environmental protection - Requirements and test methods for the spreading precision

90.93 Standard confirmed

CEN/TC 144

Wall-hung urinals - Functional requirements and test methods

90.93 Standard confirmed

CEN/TC 163

Slabs of natural stone for external paving - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression

90.93 Standard confirmed

CEN/TC 104

Windows - Behaviour between different climates - Test method

90.93 Standard confirmed

CEN/TC 33

Setts of natural stone for external paving - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Kerbs of natural stone for external paving - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Clay pavers - Requirements and test methods

90.93 Standard confirmed

CEN/TC 178

Clay pavers - Requirements and test methods

60.60 Standard published

CEN/TC 178

Swimming pool equipment - Part 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipment

90.93 Standard confirmed

CEN/TC 136

Swimming pool equipment - Part 11: Additional specific safety requirements and test methods for moveable pool floors and moveable bulkheads installed in pools for public use

60.60 Standard published

CEN/TC 136

Swimming pool equipment - Part 1: General safety requirements and test methods for equipment installed in pools for public use

60.60 Standard published

CEN/TC 136

Swimming pool equipment - Part 2: Additional specific safety requirements and test methods for ladders, stepladders and handle bends

90.93 Standard confirmed

CEN/TC 136

Swimming pool equipment - Part 3: Additional specific safety requirements and test methods for inlets and outlets and water/air based water leisure features installed in pools for public use

60.60 Standard published

CEN/TC 136

Swimming pool equipment - Part 4: Additional specific safety requirements and test methods for starting platforms

90.93 Standard confirmed

CEN/TC 136

Swimming pool equipment - Part 5: Additional specific safety requirements and test methods for lane lines and dividing line

90.93 Standard confirmed

CEN/TC 136

Swimming pool equipment - Part 6: Additional specific safety requirements and test methods for turning boards

90.93 Standard confirmed

CEN/TC 136

Swimming pool equipment - Part 7: Additional specific safety requirements and test methods for water polo goals

90.93 Standard confirmed

CEN/TC 136

Binders for floor screeds based on calcium sulphate - Part 2: Test methods

90.60 Close of review

CEN/TC 241

Chimneys - Requirements and test methods for clay/ceramic flue terminals

90.93 Standard confirmed

CEN/TC 166

Footwear - Test methods for uppers and lining - Water vapour permeability and absorption

90.60 Close of review

CEN/TC 309

Footwear - Test methods for uppers, lining and insocks - Abrasion resistance

90.60 Close of review

CEN/TC 309

Footwear - Test methods for uppers, lining and insocks - Abrasion resistance

90.92 Standard to be revised

CEN/TC 309

Coil coated metals - Test methods - Part 0: General introduction

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 11: Resistance to solvents (rubbing test)

90.20 Standard under periodical review

CEN/TC 139

Coil coated metals - Test methods - Part 1: Film thickness

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 12: Resistance to scratching

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat

90.20 Standard under periodical review

CEN/TC 139

Coil coated metals - Test methods - Part 14: Chalking (Helmen method)

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 16: Resistance to abrasion

90.93 Standard confirmed

CEN/TC 139

Coil coated metals - Test methods - Part 17: Adhesion of strippable films

90.20 Standard under periodical review

CEN/TC 139

Coil coated metals - Test methods - Part 18: Resistance to staining

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 19: Panel design and method of atmospheric exposure testing

90.20 Standard under periodical review

CEN/TC 139

Coil coated metals - Test methods - Part 20: Foam adhesion

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 2: Gloss

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

90.93 Standard confirmed

CEN/TC 139

Coil coated metals - Test methods - Part 25: Resistance to humidity

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 26: Resistance to condensation of water

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)

90.93 Standard confirmed

CEN/TC 139

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 4: Pencil hardness

90.93 Standard confirmed

CEN/TC 139

Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)

90.20 Standard under periodical review

CEN/TC 139

Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test)

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)

60.60 Standard published

CEN/TC 139

Coil coated metals - Test methods - Part 9: Resistance to water immersion

60.60 Standard published

CEN/TC 139

Shutters and blinds - Measurement of operating force - Test methods

90.93 Standard confirmed

CEN/TC 33

Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Part 1: General requirements

90.93 Standard confirmed

CEN/TC 264

Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Part 2: Specific requirements and test methods

90.93 Standard confirmed

CEN/TC 264

Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Part 3: Guide to selection, use and maintenance

90.93 Standard confirmed

CEN/TC 264

Products and systems for the protection and repair of concrete structures - Test methods - Resistance to severe chemical attack

90.93 Standard confirmed

CEN/TC 104

Pallet superstructures - Pallet collars - Test methods and performance requirements

90.93 Standard confirmed

CEN/TC 261

Protective clothing - Hand, arm, chest, abdomen, leg, foot and genital protectors for field hockey goal keepers, and shin protectors for field players - Requirements and test methods

90.60 Close of review

CEN/TC 162

Anti-flooding devices for buildings - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 165

Fixed firefighting systems - Foam systems - Part 1: Requirements and test methods for components

90.60 Close of review

CEN/TC 191

Protective clothing - Hand, arm, chest, abdomen, leg, genital and face protectors for fencers - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Static thermoplastic tanks for the above ground storage of chemicals — Blow moulded or rotationally moulded polyethylene tanks — Requirements and test methods

90.60 Close of review

CEN/TC 249

Products and systems for the protection and repair of concrete structure - Test Method - Compatibility on wet concrete

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Drying test for hydrophobic impregnation

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test Methods - Water absorption and resistance to alkali for hydrophobic impregnations

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test method - Determination of loss of mass of hydrophobic impregnated concrete after freeze-thaw salt stress

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products

90.92 Standard to be revised

CEN/TC 104

Bitumen and bituminous binders - Determination of the tensile properties of bituminous binders by the tensile test method

90.92 Standard to be revised

CEN/TC 336

Packaging - Flexible carrier bags for the transport of various retail goods - General characteristics and test methods for the determination of volume and carrying capacity

90.93 Standard confirmed

CEN/TC 261

Plastics sacks for household waste collection - Types, requirements and test methods

90.93 Standard confirmed

CEN/TC 261

Packaging - Paper sacks for household waste collection - Types, requirements and test methods

90.60 Close of review

CEN/TC 261

Protective gloves for motorcycle riders - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Copper and copper alloys - Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes

60.60 Standard published

CEN/TC 133

Chemical disinfectants - Quantitative suspension test for the evaluation of virucidal activity against bacteriophages of chemical disinfectants used in food and industrial areas - Test method and requirements (phase 2, step 1)

90.93 Standard confirmed

CEN/TC 216

Flexible hose assemblies in drinking water installations - Functional requirements and test methods

90.92 Standard to be revised

CEN/TC 164

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity against Legionella of chemical disinfectants for aqueous systems - Test method and requirements (phase 2, step 1)

60.60 Standard published

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of fungicidal or yeasticidal activity in the medical area - Test method and requirements (phase 2, step 1)

60.60 Standard published

CEN/TC 216

Packaging - Box pallets - General requirements and test methods

90.93 Standard confirmed

CEN/TC 261

Protective footwear for motorcycle riders - Requirements and test methods

90.60 Close of review

CEN/TC 161

Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Metal lath and beads - Definitions, requirements and test methods - Part 1: Internal plastering

60.60 Standard published

CEN/TC 241

Metal lath and beads - Definitions, requirements and test methods - Part 2: External rendering

60.60 Standard published

CEN/TC 241

Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 1: Freeze-thaw cycling with de-icing salt immersion

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock)

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 3: Thermal cycling without de-icing salt impact

90.60 Close of review

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 4: Dry thermal cycling

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 5: Resistance to temperature shock

90.60 Close of review

CEN/TC 104

Wood flooring - Test methods to determine elasticity and resistance to wear and impact resistance

90.93 Standard confirmed

CEN/TC 175

Chemical disinfectants and antiseptics - Quantitative non-porous surface test for the evaluation of bactericidal and yeasticidal and/or fungicidal activity of chemical disinfectants used in food, industrial, domestic and institutional areas without mechanical action - Test method and requirements without mechanical action (phase 2, step 2)

60.60 Standard published

CEN/TC 216

Chemical disinfectants - Quantitative suspension test for the evaluation of sporicidal activity of chemical disinfectants used in food, industrial, domestic and institutional areas - Test method and requirements (phase 2, step 1)

90.92 Standard to be revised

CEN/TC 216

Postal services - Apertures of private letter boxes and letter plates - Requirements and test methods

90.93 Standard confirmed

CEN/TC 331

Postal services - Apertures of private letter boxes and letter plates - Requirements and test methods

60.60 Standard published

CEN/TC 331

Test methods for wound dressings - Aspects of absorption, moisture vapour transmission, waterproofness and extensibility

60.60 Standard published

CEN/TC 205

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity in the medical area - Test method and requirements (phase 2, step 1)

90.60 Close of review

CEN/TC 216

Agricultural machinery - Solid fertilizer broadcasters and full width distributors - Environmental protection - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 144

Agricultural machinery - Solid fertilizer broadcasters and full width distributors - Environmental protection - Part 2: Test methods

60.60 Standard published

CEN/TC 144

Agricultural machinery - Solid fertilizer line-distributors - Environmental protection - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 144

Irrigation techniques - Solid set sprinkler systems - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 334

Domestic water kettles for use on top of stove, cooker or hob - Requirements and test methods

90.60 Close of review

CEN/TC 194

Natural stone test methods - Determination of water absorption at atmospheric pressure

90.60 Close of review

CEN/TC 246

Furniture - Operating mechanisms for seating and sofa-beds - Test methods

90.93 Standard confirmed

CEN/TC 207

Compressors and condensing units for refrigeration - Performance testing and test methods - Part 1: Refrigerant compressors

90.60 Close of review

CEN/TC 113

Compressors and condensing units for refrigeration - Performance testing and test methods - Part 2: Condensing units

90.93 Standard confirmed

CEN/TC 113

Surgical clothing and drapes - Requirements and test methods - Part 1: Surgical drapes and gowns

60.60 Standard published

CEN/TC 205

Surgical clothing and drapes - Requirements and test methods - Part 2: Clean air suits

60.60 Standard published

CEN/TC 205

Timber structures - Test methods - Load bearing nails, screws, dowels and bolts

90.93 Standard confirmed

CEN/TC 124

Timber structures - Test methods - Load bearing stapled joints

90.93 Standard confirmed

CEN/TC 124

Fibrous gypsum plaster casts - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Hearing protectors - Testing - Part 1: Physical test methods

60.60 Standard published

CEN/TC 159

Hearing protectors - Testing - Part 2: Acoustic test methods

60.60 Standard published

CEN/TC 159

Hearing protectors - Testing - Part 3: Supplementary acoustic test methods

60.60 Standard published

CEN/TC 159

Timber Structures - Test methods - Withdrawal capacity of timber fasteners

90.93 Standard confirmed

CEN/TC 124

Timber structures - Test methods - Pull through resistance of timber fasteners

90.93 Standard confirmed

CEN/TC 124

Footwear protecting against chemicals - Part 1: Terminology and test methods

90.92 Standard to be revised

CEN/TC 161

Roller sports equipment - Inline-skates - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Manufactured articles solely filled with feathers and down - Measurement of thickness and compressibility of cushions - Part 1: Test method by rotation

90.93 Standard confirmed

CEN/TC 222

Manufactured articles solely filled with feathers and down - Measurement of thickness and compressibility of cushions - Part 2: Test method by oscillation

90.93 Standard confirmed

CEN/TC 222

Concrete pavements - Part 1: Test method for the determination of the thickness of a concrete pavement by survey method

90.93 Standard confirmed

CEN/TC 227

Concrete pavements - Part 2: Test method for the determination of the bond between two layers

90.93 Standard confirmed

CEN/TC 227

Concrete pavements - Part 3: Test methods for the determination of the thickness of a concrete pavement from cores

90.93 Standard confirmed

CEN/TC 227

Concrete pavements - Part 4: Test methods for the determination of wear resistance of concrete pavements to studded tyres

90.60 Close of review

CEN/TC 227

Concrete pavements - Part 6: Test method for the determination of the tensile strength of concrete on cylindrical discs

60.60 Standard published

CEN/TC 227

Catheters - Test methods for kinking of single lumen catheters and medical tubing

90.93 Standard confirmed

CEN/TC 205

Lighters - Child safety requirements for lighters - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 355

Hot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression

90.60 Close of review

CEN/TC 227

Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements

90.92 Standard to be revised

CEN/TC 227

Hot applied joint sealants - Part 1: Test method for the determination of density at 25 °C

90.93 Standard confirmed

CEN/TC 227

Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)

90.93 Standard confirmed

CEN/TC 227

Hot applied joint sealants - Part 13: Test method for the determination of the discontinuous extension (adherence test)

90.60 Close of review

CEN/TC 227

Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C

90.60 Close of review

CEN/TC 227

Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience)

60.60 Standard published

CEN/TC 227

Hot applied joint sealants - Part 4: Test method for the characterization of heat resistance - Change in penetration value

60.60 Standard published

CEN/TC 227

Hot applied joint sealants - Part 5: Test method for the determination of flow resistance

60.60 Standard published

CEN/TC 227

Hot applied joint sealants - Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion

90.60 Close of review

CEN/TC 227

Hot applied joint sealants - Part 9: Test method for the determination of compatibility with asphalt pavements

90.93 Standard confirmed

CEN/TC 227

Grouts for ceramic tiles - Part 2: Test methods

60.60 Standard published

CEN/TC 67

Products and systems for the protection and repair of concrete structures - Test methods - Determination of fatigue under dynamic loading - Part 1: During cure

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of fatigue under dynamic loading - Part 2: After hardening

90.93 Standard confirmed

CEN/TC 104

Roller sports equipment - Roller skates - Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Protective clothing for firefighters - Requirements and test methods for fire hoods for firefighters

60.60 Standard published

CEN/TC 162

Prefabricated gypsum plasterboard panels with a cellular paperboard core - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Gypsum board thermal/acoustic insulation composite panels - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Jointing materials for gypsum boards - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Suspended ceilings - Requirements and test methods

90.60 Close of review

CEN/TC 277

Derivatives from coal pyrolysis - Coal tar based oils: creosotes - Specifications and test methods

60.60 Standard published

CEN/TC 317

Child use and care articles - Soothers for babies and young children - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Binders for magnesite screeds - Caustic magnesia and magnesium chloride - Part 2: Test methods

90.93 Standard confirmed

CEN/TC 303

Stone shields for off-road motorcycling suited to protect riders against stones and debris - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Child use and care articles - Baby bouncers - Safety requirements and test methods

90.60 Close of review

CEN/TC 252

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 2: Pre-fabricated ceiling mounted radiant panels for space heating - Test method for thermal output

90.93 Standard confirmed

CEN/TC 130

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity

90.93 Standard confirmed

CEN/TC 130

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 5: Open or closed heated ceiling surfaces - Test method for thermal output

90.93 Standard confirmed

CEN/TC 130

High rise aerial appliances for fire and rescue service use - Turntable ladders with combined movements - Safety and performance requirements and test methods

90.60 Close of review

CEN/TC 192

High rise aerial appliances for fire and rescue service use - Turntable ladders with sequential movements - Safety and performance requirements and test methods

90.60 Close of review

CEN/TC 192

Decorative oil lamps - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 46

Natural stone test methods - Determination of resistance to ageing by thermal shock

90.60 Close of review

CEN/TC 246

Products and systems for the protection and repair of concrete structures - Test methods - Determination of watertightness of injected cracks without movement in concrete

90.93 Standard confirmed

CEN/TC 104

Glass in furniture - Test methods

90.60 Close of review

CEN/TC 207

Non-active medical devices - Performance requirements and test methods for absorbent cotton gauze and absorbent cotton and viscose gauze

90.93 Standard confirmed

CEN/TC 205

Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products

90.93 Standard confirmed

CEN/TC 104

Protective clothing - Wrist, palm, knee and elbow protectors for users of roller sports equipment - Requirements and test methods

90.60 Close of review

CEN/TC 162

Natural stone test methods - Determination of the dynamic modulus of elasticity (by measuring the fundamental resonance frequency)

90.60 Close of review

CEN/TC 246

Derivatives from coal pyrolysis - Carbon black feedstock - Specifications and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar based oils: Coal tar fuel - Specifications and test methods

90.93 Standard confirmed

CEN/TC 317

Natural stone test methods - Determination of the abrasion resistance

90.60 Close of review

CEN/TC 246

Natural stone test methods - Determination of rupture energy

90.60 Close of review

CEN/TC 246

Fume cupboards - Part 3: Type test methods

90.60 Close of review

CEN/TC 332

Fume cupboards - Part 4: On-site test methods

90.93 Standard confirmed

CEN/TC 332

Cold applied joint sealants - Test methods - Part 1: Determination of rate of cure

90.60 Close of review

CEN/TC 227

Cold applied joint sealants - Test methods - Part 2: Determination of tack free time

90.93 Standard confirmed

CEN/TC 227

Cold applied joint sealants - Test methods - Part 3: Determination of self-levelling properties

90.93 Standard confirmed

CEN/TC 227

Cold applied joint sealants - Test methods - Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals

90.93 Standard confirmed

CEN/TC 227

Cold applied joint sealants - Test methods - Part 5: Determination of the resistance to hydrolysis

90.60 Close of review

CEN/TC 227

Cold applied joint sealants - Test method - Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals

90.93 Standard confirmed

CEN/TC 227

Cold applied joint sealants - Test methods - Part 7: Determination of the resistance to flame

90.60 Close of review

CEN/TC 227

Cold applied joint sealants - Test methods - Part 8: Determination of the artificial weathering by UV-irradiation

90.93 Standard confirmed

CEN/TC 227

Cold applied joint sealants - Test methods - Part 9: Function testing of joint sealants

90.60 Close of review

CEN/TC 227

Gypsum board products from reprocessing - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Metal framing components for gypsum board systems - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers

90.93 Standard confirmed

CEN/TC 189

Blinds and shutters - Suitability for use of tubular and square motorizations - Requirements and test methods

90.92 Standard to be revised

CEN/TC 33

Blinds and shutters - Capability for use of gears with crank handle - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of mycobactericidal activity of chemical disinfectants and antiseptics used in the veterinary area - Test method and requirements (phase 2, step 1)

90.93 Standard confirmed

CEN/TC 216

Preformed plasterboard cornices - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Liquid petroleum products - Fatty acid methyl esters (FAME) for use in diesel engines and heating applications - Requirements and test methods

60.60 Standard published

CEN/TC 19

Sterilizers for medical purposes - Ethylene oxide sterilizers - Requirements and test methods

90.93 Standard confirmed

CEN/TC 102

Diving suits - Part 1: Wet suits - Requirements and test methods

90.60 Close of review

CEN/TC 162

Diving suits - Part 2: Dry suits - Requirements and test methods

90.60 Close of review

CEN/TC 162

Diving suits - Part 3: Actively heated or cooled suit systems and components - Requirements and test methods

90.60 Close of review

CEN/TC 162

Natural stone test methods - Determination of the slip resistance by means of the pendulum tester

90.93 Standard confirmed

CEN/TC 246

Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners

90.60 Close of review

CEN/TC 166

Gypsum elements for suspended ceilings - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Gypsum elements for suspended ceilings - Definitions, requirements and test methods

60.60 Standard published

CEN/TC 241

Structural round timber - Test methods

90.93 Standard confirmed

CEN/TC 124

Adhesives for non-structural wood applications - Test method and requirements for resistance to static load

90.60 Close of review

CEN/TC 193

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : road tars - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : refractory binders - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : briquetting pitch - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : carbon binder pitch - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : impregnating pitch - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : painting tar - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Derivatives from coal pyrolysis - Coal tar and pitch based binders and related products : coating tar - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Chimneys - Freeze-thaw resistance test method for chimney products

90.93 Standard confirmed

CEN/TC 166

Swap bodies - Swap tanks - Dimensions, requirements, test methods, operation conditions

90.93 Standard confirmed

CEN/TC 119

Wood-based panels - Melamine faced boards for interior uses - Test methods

60.60 Standard published

CEN/TC 112

Protective clothing against chemicals - Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages

60.60 Standard published

CEN/TC 162

Protective clothing - Gloves and armguards protecting against cuts by powered knives - Requirements and test methods

90.60 Close of review

CEN/TC 162

Child care articles - Child seats for cycles - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Chemical disinfectants and antiseptics - Basic sporicidal activity - Test method and requirements (phase 1)

90.93 Standard confirmed

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of mycobactericidal activity of chemical disinfectants in the medical area including instrument disinfectants - Test methods and requirements (phase 2, step 1)

90.93 Standard confirmed

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative surface test for the evaluation of bactericidal activity of chemical disinfectants and antiseptics used in the veterinary area on non-porous surfaces without mechanical action - Test method and requirements (phase 2, step 2)

90.93 Standard confirmed

CEN/TC 216

Child care articles - Drinking equipment - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Metal beads and feature profiles for use with gypsum plasterboards - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Road marking materials - Road marking performance for road users and test methods

90.60 Close of review

CEN/TC 226

Surface active agents - Determination of foamability and degree of foamability - Circulation test method

90.93 Standard confirmed

CEN/TC 276

Influence of organic materials on water intended for human consumption - Organoleptic assessment of water in storage systems - Part 1: Test method

90.93 Standard confirmed

CEN/TC 164

Personal protective equipment - Knee protectors for work in the kneeling position - Part 1: Test methods

60.60 Standard published

CEN/TC 162

Products and systems for the protection and repair of concrete structures - Test methods - Determination of the expansion ratio and expansion evolution

90.93 Standard confirmed

CEN/TC 104

Geosynthetics - Screening test method for determining chemical resistance for landfill applications

90.93 Standard confirmed

CEN/TC 189

Geosynthetic barriers - Test method for determining the resistance to leaching

90.93 Standard confirmed

CEN/TC 189

Shower enclosures - Functional requirements and test methods

90.93 Standard confirmed

CEN/TC 163

Writing boards for educational institutions - Ergonomic, technical and safety requirements and their test methods

60.60 Standard published

CEN/TC 207

Determination of the uplift resistance of installed clay or concrete tiles for roofing - Roof system test method

60.60 Standard published

CEN/TC 128

Table tennis - Part 1: Table tennis tables, functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Table tennis - Part 2: Posts for net assemblies - Requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Chimneys - System chimneys with plastic flue liners - Requirements and test methods

90.93 Standard confirmed

CEN/TC 166

Precast concrete products - Concrete with wood-chips as aggregate - Requirements and test methods

90.60 Close of review

CEN/TC 229

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of virucidal activity in the medical area - Test method and requirements (Phase 2/Step 1)

90.92 Standard to be revised

CEN/TC 216

Packaging - Flexible packaging material - Determination of puncture resistance - Test methods

90.93 Standard confirmed

CEN/TC 261

Materials and articles in contact with foodstuffs - Plastics - Test methods for the determination of fatty contact

90.93 Standard confirmed

CEN/TC 194

Postal services - Trays for international letter mail - Test methods and performance requirements

90.93 Standard confirmed

CEN/TC 331

Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods

90.60 Close of review

CEN/TC 241

Products and systems for the protection and repair of concrete structures - Test methods - Determination of the filtration stability

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of the filtration stability

60.60 Standard published

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles

90.93 Standard confirmed

CEN/TC 104

Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 3: Test methods

60.60 Standard published

CEN/TC 113

Bidets - Functional requirements and test methods

90.92 Standard to be revised

CEN/TC 163

Welding consumables - Test methods and quality requirements - Part 1: Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys

90.92 Standard to be revised

CEN/TC 121

Welding consumables - Test methods and quality requirements - Part 2: Supplementary methods and conformity assessment of consumables for steel, nickel and nickel alloys

90.92 Standard to be revised

CEN/TC 121

Welding consumables - Test methods and quality requirements - Part 3: Conformity assessment of wire electrodes, wires and rods for welding of aluminium alloys

90.92 Standard to be revised

CEN/TC 121

Chemical disinfectants and antiseptics - Quantitative carrier test for the evaluation of bactericidal activity for instruments used in the medical area - Test method and requirements (phase 2, step 2)

90.60 Close of review

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative carrier test for the evaluation of fungicidal or yeasticidal activity for instruments used in the medical area - Test method and requirements (phase 2, step 2)

90.60 Close of review

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative carrier test for the evaluation of mycobactericidal or tuberculocidal activity of chemical disinfectants used for instruments in the medical area - Test method and requirements (phase 2, step 2)

90.60 Close of review

CEN/TC 216

Mechanical fasteners for gypsum plasterboard systems - Definitions, requirements and test methods

60.60 Standard published

CEN/TC 241

Chimneys - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods

60.60 Standard published

CEN/TC 166

Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods

60.60 Standard published

CEN/TC 166

Geosynthetic barriers - Screening test method for determining the resistance to oxidation

90.93 Standard confirmed

CEN/TC 189

Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking

90.93 Standard confirmed

CEN/TC 189

Natural stone test methods - Determination of sound speed propagation

90.93 Standard confirmed

CEN/TC 246

Natural stone test methods - Determination of static elastic modulus

90.60 Close of review

CEN/TC 246

Natural stone test methods - Determination of linear thermal expansion coefficient

90.93 Standard confirmed

CEN/TC 246

Footwear - Test methods for the assessment of ecological criteria

90.60 Close of review

CEN/TC 309

Agglomerated stone - Test methods - Part 10: Determination of chemical resistance

90.92 Standard to be revised

CEN/TC 246

Agglomerated stone - Test methods - Part 11: Determination of linear thermal expansion coefficient

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 1: Determination of apparent density and water absorption

90.60 Close of review

CEN/TC 246

Agglomerated stone - Test methods - Part 12: Determination of dimensional stability

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity

90.60 Close of review

CEN/TC 246

Agglomerated stone - Test methods - Part 16: Determination of dimensions, geometric characteristics and surface quality of modular tiles

90.92 Standard to be revised

CEN/TC 246

Agglomerated stone - Test methods - Part 2: Determination of flexural strength (bending)

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 4: Determination of the abrasion resistance

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 5: Determination of freeze and thaw resistance

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 6: Determination of thermal shock resistance

90.93 Standard confirmed

CEN/TC 246

Agglomerated stone - Test methods - Part 9: Determination of impact resistance

90.93 Standard confirmed

CEN/TC 246

Roller sports equipment - Kick scooters - Safety requirements and test methods

90.20 Standard under periodical review

CEN/TC 136

Ductile iron pipes, fittings and accessories - Requirements and test methods - Part 1: PE coatings

60.60 Standard published

CEN/TC 203

Products and systems for the protection and repair of concrete structures - Test methods - Determination of chloride content in hardened concrete

90.60 Close of review

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of carbonation depth in hardened concrete by the phenolphthalein method

90.93 Standard confirmed

CEN/TC 104

Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies - Requirements, test methods, application and maintenance

90.93 Standard confirmed

CEN/TC 33

Crude tar and crude benzole - Characteristics and test methods

90.93 Standard confirmed

CEN/TC 317

Building hardware - Fittings for shutters - Requirements and test methods

60.60 Standard published

CEN/TC 33

Precast concrete products - Test method for strength retention of glass fibres in cement and concrete (SIC TEST)

90.93 Standard confirmed

CEN/TC 229

Test method for metallic fibre concrete - Measuring the flexural tensile strength (limit of proportionality (LOP), residual)

90.93 Standard confirmed

CEN/TC 229

Child care articles - Carry cots and stands for domestic use - Safety requirements and test methods

60.60 Standard published

CEN/TC 252

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of virucidal activity of chemical disinfectants and antiseptics used in the veterinary area - Test method and requirements (Phase 2, step 1)

90.93 Standard confirmed

CEN/TC 216

Medical face masks - Requirements and test methods

90.00 Start of review/2 Year Review Enquiry

CEN/TC 205

Sanitary appliances - Wash basins - Functional requirements and test methods

90.93 Standard confirmed

CEN/TC 163

Furniture - Links for non-domestic seating linked together in a row - Strength requirements and test methods

90.93 Standard confirmed

CEN/TC 207

Stretched ceilings - Requirements and test methods

90.93 Standard confirmed

CEN/TC 357

Influence of organic materials on water intended for human consumption - Determination of the chlorine demand - Test method

90.93 Standard confirmed

CEN/TC 164

Test method for metallic fibre concrete - Measuring the fibre content in fresh and hardened concrete

90.93 Standard confirmed

CEN/TC 229

Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure

90.93 Standard confirmed

CEN/TC 155

Furniture - Domestic and kitchen storage units and kitchen-worktops - Safety requirements and test methods

60.60 Standard published

CEN/TC 207

Fasteners - Tightening performance - Torque/Angle simplified test method

90.93 Standard confirmed

CEN/TC 185

Surfaces for sports areas - Synthetic surfaces for outdoor sports areas - Test method for artificial weathering

90.93 Standard confirmed

CEN/TC 217

Joint fillers and sealants - Test methods for preformed joint seals

90.93 Standard confirmed

CEN/TC 227

Test methods for fibres in concrete - Part 1: Reference concretes

90.93 Standard confirmed

CEN/TC 104

Test methods for fibres in concrete - Part 2: Effect on concrete

90.93 Standard confirmed

CEN/TC 104

Building hardware - Locks and latches - Electromechanically operated locks and striking plates - Requirements and test methods

60.60 Standard published

CEN/TC 33

Protective clothing for fire-fighters - Test methods and requirements for reflective clothing for specialised fire-fighting

90.60 Close of review

CEN/TC 162

Packaging - Plastic freezer bags - Specifications and test methods

90.93 Standard confirmed

CEN/TC 261

Structural adhesives - Determination of shear behaviour of structural bonds - Part 1: Torsion test method using butt-bonded hollow cylinders (ISO 11003-1:2001, modified)

90.93 Standard confirmed

CEN/TC 193

Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements, test methods, assessment and verification of constancy of performance, classification and marking

90.60 Close of review

CEN/TC 67

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)

60.60 Standard published

CEN/TC 203

Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods

90.60 Close of review

CEN/TC 203

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 2: Thermoplastic acid modified polyolefin coating (TMPO)

60.60 Standard published

CEN/TC 203

Surfaces for sports areas - Multi-sports floor systems for indoor use - Test method for determination of rotational friction

90.60 Close of review

CEN/TC 217

Leather - Leather for automotive - Test methods and testing parameters

90.92 Standard to be revised

CEN/TC 289

Influence of cementitious products on water intended for human consumption - Test methods - Part 1: Influence of factory made cementitious products on organoleptic parameters

60.60 Standard published

CEN/TC 164

Influence of cementitious products on water intended for human consumption - Test methods - Part 3: Migration of substances from factory-made cementititous products

60.60 Standard published

CEN/TC 164

Inflatable play equipment - Part 1: Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Inflatable play equipment - Part 3: Additional safety requirements and test methods for snappies

60.60 Standard published

CEN/TC 136

Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods

60.60 Standard published

CEN/TC 128

Skateparks - Safety requirements and test methods

90.60 Close of review

CEN/TC 136

Textiles - Mattress ticking - Specifications and test methods

90.93 Standard confirmed

CEN/TC 248

Children's high chairs - Requirements and test methods

60.60 Standard published

CEN/TC 364

Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 1: Vertical air/flue terminals for C6-type appliances

90.93 Standard confirmed

CEN/TC 166

Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 2: Flue and air supply ducts for room sealed appliances

90.92 Standard to be revised

CEN/TC 166

Chemical disinfectants and antiseptics - Hygienic handwash - Test method and requirements (phase 2/step 2)

90.93 Standard confirmed

CEN/TC 216

Derivatives from coal pyrolysis - Coal tar based oils: fluxings oils - Specifications and test methods

90.93 Standard confirmed

CEN/TC 317

Chemical disinfectants and antiseptics - Hygienic handrub - Test method and requirements (phase 2/step 2)

90.60 Close of review

CEN/TC 216

Railway applications - Rescue coupler - Performance requirements, specific interface geometry and test methods

60.60 Standard published

CEN/TC 256

Workplace exposure - Measurement of the dustiness of bulk materials - Part 1: Requirements and choice of test methods

90.93 Standard confirmed

CEN/TC 137

Fibre cement profiled sheets - Impact resistance test method

90.93 Standard confirmed

CEN/TC 128

Playing field equipment - Badminton equipment - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Playing field equipment - Tennis equipment - Functional and safety requirements, test methods

90.93 Standard confirmed

CEN/TC 136

Container shells for mobile waste containers with a capacity up to 1 700 l - Performance requirements and test methods

90.93 Standard confirmed

CEN/TC 183

Mountaineering equipment - Braking devices - Part 1: Braking devices with manually assisted locking, safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Mountaineering equipment - Braking devices - Part 2: Manual braking devices, safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Products and systems for the protection and repair of concrete structures - Test methods - Corrosion protection test

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)

90.93 Standard confirmed

CEN/TC 104

Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods

90.93 Standard confirmed

CEN/TC 203

Structural adhesives - Test methods for assessing long term durability of bonded metallic structures

90.93 Standard confirmed

CEN/TC 193

Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling - Terms, definitions, test conditions, test methods and requirements

60.60 Standard published

CEN/TC 113

Windows, doors, shutters and blinds - Bullet resistance - Test method

90.60 Close of review

CEN/TC 33

Slow heat release appliances fired by solid fuel - Requirements and test methods

90.93 Standard confirmed

CEN/TC 295

Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods

90.20 Standard under periodical review

CEN/TC 33

General purpose adhesives for structural assembly - Requirements and test methods

90.93 Standard confirmed

CEN/TC 193

Fixed firefighting systems - Condensed aerosol extinguishing systems - Part 1: Requirements and test methods for components

60.60 Standard published

CEN/TC 191

Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement

90.60 Close of review

CEN/TC 241

Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 2: Gypsum fibre boards

90.60 Close of review

CEN/TC 241

Materials and articles in contact with food stuffs - Test method for the resistance to microwave heating of ceramic, glass, glass-ceramic or plastics cookware

90.60 Close of review

CEN/TC 194

Automotive fuels - Automotive ethanol (E85) fuel - Requirements and test methods

90.93 Standard confirmed

CEN/TC 19

Non-destructive Testing - Test Method for Residual Stress analysis by X-ray Diffraction

90.93 Standard confirmed

CEN/TC 138

Non-destructive Testing - Test Method for Residual Stress analysis by X-ray Diffraction

60.60 Standard published

CEN/TC 138

Free access multi-sports equipment - Requirements, including safety and test methods

90.92 Standard to be revised

CEN/TC 136

Wood flooring - Determination of bending strength under static load - Test methods

90.93 Standard confirmed

CEN/TC 175

Wood flooring and parquet - Determination of resistance to indentation - Test method

60.60 Standard published

CEN/TC 175

Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods

90.93 Standard confirmed

CEN/TC 19

Packaging - Test method to determine the porosity of the internal coating of flexible aluminium tubes - Part 1: Sodium chloride test

90.93 Standard confirmed

CEN/TC 261

Packaging - Test method to determine the porosity of the internal coating of flexible aluminium tubes - Part 2: Copper sulphate test

90.60 Close of review

CEN/TC 261

Packaging - Flexible laminate tubes - Test methods to determine the strength of the head welding

90.60 Close of review

CEN/TC 261

Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion

90.93 Standard confirmed

CEN/TC 261

Packaging - Flexible laminate tubes - Test methods to assess the strength of the side seam

90.93 Standard confirmed

CEN/TC 261

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 1: Long-term tension load test perpendicular to the bond line at varying climate conditions with specimens perpendicular to the glue line (Glass house test)

90.92 Standard to be revised

CEN/TC 193

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear

90.92 Standard to be revised

CEN/TC 193

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions

90.92 Standard to be revised

CEN/TC 193

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions

90.92 Standard to be revised

CEN/TC 193

Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off

90.93 Standard confirmed

CEN/TC 104

Sweepers - Part 2: Performance requirements and test methods

90.93 Standard confirmed

CEN/TC 337

Products and systems for the protection and repair of concrete structures - Test methods - Determination of tensile strength development for polymers

90.93 Standard confirmed

CEN/TC 104

Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep under sustained tensile load for synthetic resin products (PC) for the anchoring of reinforcing bars

90.93 Standard confirmed

CEN/TC 104

Petroleum products - Test method for free water in liquefied petroleum gas by visual inspection

90.93 Standard confirmed

CEN/TC 19

Cycles - Requirements and test methods for cycle locks

90.92 Standard to be revised

CEN/TC 333

Composites made from cellulose-based materials and thermoplastics (usually called wood-polymer composites (WPC) or natural fibre composites (NFC)) - Part 1: Test methods for characterisation of compounds and products

90.00 Start of review/2 Year Review Enquiry

CEN/TC 249

Derivatives from coal pyrolysis - Coal tar based oils: wash oils - Specifications and test methods

90.93 Standard confirmed

CEN/TC 317

Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods

90.93 Standard confirmed

CEN/TC 203

Precast concrete products - Resin bound concrete - Requirements and test methods

90.60 Close of review

CEN/TC 229

Textiles - Terry fabrics - Test method for the determination of the resistance to pile loop extraction

90.93 Standard confirmed

CEN/TC 248

Knee and elbow protectors for indoor sports - Safety requirements and test methods

90.60 Close of review

CEN/TC 162

District heating pipes - Factory made flexible pipe systems - Part 1: Classification, general requirements and test methods

60.60 Standard published

CEN/TC 107

District heating pipes - Factory made flexible pipe systems - Part 2: Bonded system with plastic service pipes; requirements and test methods

60.60 Standard published

CEN/TC 107

District heating pipes - Factory made flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods

60.60 Standard published

CEN/TC 107

District heating pipes - Factory made flexible pipe systems - Part 4: Bonded system with metal service pipes; requirements and test methods

60.60 Standard published

CEN/TC 107

Sanitary appliances - Shower trays made from impact modified extruded acrylic sheets - Requirements and test methods

90.60 Close of review

CEN/TC 163

Ice skates - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Electrodeposited coatings - Electroplated coatings of aluminium and aluminium alloys with supplementary treatment - Requirements and test methods

90.60 Close of review

CEN/TC 262

Packaging - Flexible aluminium tubes - Test method to check the resistance of the internal protective coating against ammonia

90.93 Standard confirmed

CEN/TC 261

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 1: Polyurethane lining of pipes and fittings

90.60 Close of review

CEN/TC 203

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of pipes

60.60 Standard published

CEN/TC 203

Building hardware - Mechatronic cylinders - Requirements and test methods

60.60 Standard published

CEN/TC 33

Building hardware - Requirements and test methods - Multipoint locks, latches and locking plates - Characteristics and test methods

60.60 Standard published

CEN/TC 33

Plastics - Thermoplastic jackets for insulation products for building equipment and industrial installations - Requirements and test methods

90.93 Standard confirmed

CEN/TC 249

Sanitary appliances - Baths made from impact modified coextruded ABS/acrylic sheets - Requirements and test methods

90.93 Standard confirmed

CEN/TC 163

Sanitary appliances - Shower trays made from impact modified coextruded ABS/acrylic sheets - Requirements and test methods

90.60 Close of review

CEN/TC 163

Railway applications - Braking systems of high speed trains - Part 2: Test methods

90.60 Close of review

CEN/TC 256

Railway applications - Braking systems of high speed trains - Part 2: Test methods

60.60 Standard published

CEN/TC 256

Timber Structures - Test methods - Withdrawal capacity of punched metal plate fasteners in handling and erection of prefabricated trusses

60.60 Standard published

CEN/TC 124

Timber Structures - Test methods - Torsional resistance of driving in screws

90.93 Standard confirmed

CEN/TC 124

Packaging - Flexible aluminium tubes - Test methods to determine the polymerization of the internal coating with acetone

90.93 Standard confirmed

CEN/TC 261

Conservation of cultural property - Test methods - Determination of water absorption by capillarity

90.93 Standard confirmed

CEN/TC 346

Conservation of cultural property - Test methods - Determination of static contact angle

90.93 Standard confirmed

CEN/TC 346

Conservation of cultural property - Test methods - Determination of water vapour permeability (δp)

90.93 Standard confirmed

CEN/TC 346

Multi-firing sauna stoves fired by natural wood logs - Requirements and test methods

60.60 Standard published

CEN/TC 295

Rough-terrain variable reach trucks - Visibility - Test methods and verification

60.60 Standard published

CEN/TC 150

Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods

90.93 Standard confirmed

CEN/TC 249

Conservation of cultural property - Test methods - Colour measurement of surfaces

90.93 Standard confirmed

CEN/TC 346

Fire-fighting hoses - Test methods

90.93 Standard confirmed

CEN/TC 192

Cycles - Cycle trailers - Safety requirements and test methods

90.60 Close of review

CEN/TC 333

Fibres - Elasticity of fibres - Test methods

90.93 Standard confirmed

CEN/TC 248

Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods

90.00 Start of review/2 Year Review Enquiry

CEN/TC 19

Automotive fuels - Paraffinic diesel fuel from synthesis or hydrotreatment - Requirements and test methods

60.60 Standard published

CEN/TC 19

Pyrotechnic articles - Fireworks, Categories F1, F2 and F3 - Part 4: Test methods

60.60 Standard published

CEN/TC 212

Breath alcohol test devices other than single use devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 367

All terrain vehicles (ATVs - Quads) - Safety requirements and test methods

90.92 Standard to be revised

CEN/TC 354

All terrain vehicles (ATVs - Quads) - Safety requirements and test methods

60.60 Standard published

CEN/TC 354

Power operated pedestrian doorsets - Safety in use - Requirements and test methods

60.60 Standard published

CEN/TC 33

Railway applications - Automatic coupler - Performance requirements, specific interface geometry and test method

90.20 Standard under periodical review

CEN/TC 256

Ride-on, motorized vehicles intended for the transportation of persons and not intended for use on public roads - Single-track two-wheel motor vehicles - Safety requirements and test methods

90.60 Close of review

CEN/TC 354

Inflation devices and accessories for inflatable consumer products - Part 2: Safety requirements, durability, performance, compatibility and test methods of inflators

90.93 Standard confirmed

CEN/TC 136

BMX bicycles - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 333

Influence of metallic materials on water intended for human consumption - Dynamic rig test for assessment of surface coatings with nickel layers - Long-term test method

90.60 Close of review

CEN/TC 164

Paddles and oars for recreational boats - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Laminate floor coverings - Test method for the determination of micro-scratch resistance

60.60 Standard published

CEN/TC 134

Domestic and non-domestic storage furniture - Test methods for the determination of strength, durability and stability

90.93 Standard confirmed

CEN/TC 207

Domestic and non-domestic storage furniture - Test methods for the determination of strength, durability and stability

60.60 Standard published

CEN/TC 207

Natural stone test methods - Determination of sensitivity to changes in appearance produced by thermal cycles

90.93 Standard confirmed

CEN/TC 246

Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods

90.60 Close of review

CEN/TC 128

Railway applications - Braking systems of multiple unit trains - Part 2: Test methods

90.60 Close of review

CEN/TC 256

Railway applications - Braking systems of multiple unit trains - Part 2: Test methods

60.60 Standard published

CEN/TC 256

Motorcyclists' protective clothing against mechanical impact - Part 1: Motorcyclists' limb joint impact protectors - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Motorcyclists' protective clothing against mechanical impact - Part 2: Motorcyclists' back protectors - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Motorcyclists' protective clothing against mechanical impact — Part 3: Motorcyclists' chest protectors - Requirements and test methods

90.60 Close of review

CEN/TC 162

Motorcyclists' protective clothing against mechanical impact - Part 4: Motorcyclists' inflatable protectors - Requirements and test methods

90.92 Standard to be revised

CEN/TC 162

Leisure karts - Part 1: Safety requirements and test methods for karts

90.92 Standard to be revised

CEN/TC 354

Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods

90.93 Standard confirmed

CEN/TC 128

Pyrotechnic articles - Theatrical pyrotechnic articles - Part 5: Test methods

60.60 Standard published

CEN/TC 212

Pyrotechnic articles - Fireworks, Category 4 - Part 3: Test methods

60.60 Standard published

CEN/TC 212

Pyrotechnic articles - Other pyrotechnic articles - Part 4: Test methods

60.60 Standard published

CEN/TC 212

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 1: Intrinsic characteristics - Sound absorption under diffuse sound field conditions

60.60 Standard published

CEN/TC 256

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 2: Intrinsic characteristics - Airborne sound insulation under diffuse sound field conditions

60.60 Standard published

CEN/TC 256

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-1: Normalized railway noise spectrum and single number ratings for diffuse sound field applications

60.60 Standard published

CEN/TC 256

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 3-2: Normalized railway noise spectrum and single number ratings for direct sound field applications

60.60 Standard published

CEN/TC 256

Railway applications - Track - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 4: Intrinsic characteristics - In situ values of sound diffraction under direct sound field

90.93 Standard confirmed

CEN/TC 256

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 5: Intrinsic characteristics - Sound absorption under direct sound field conditions

60.60 Standard published

CEN/TC 256

Railway applications - Infrastructure - Noise barriers and related devices acting on airborne sound propagation - Test method for determining the acoustic performance - Part 6: Intrinsic characteristics - Airborne sound insulation under direct sound field conditions

60.60 Standard published

CEN/TC 256

Breath alcohol test devices for general public - Requirements and test methods

90.93 Standard confirmed

CEN/TC 367

Child protective products - Consumer fitted child resistant locking devices for windows and balcony doors - Safety requirements and test methods

90.60 Close of review

CEN/TC 252

Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance under static loading

60.60 Standard published

CEN/TC 33

Packaging - Flexible aluminium tubes - Test method to measure the force to pierce the membrane

90.93 Standard confirmed

CEN/TC 261

Packaging - Flexible laminate and plastic tubes - Test method to determine the adhesive strength of the membrane

90.60 Close of review

CEN/TC 261

Packaging - Flexible aluminium tubes - Test method to measure the deformation of the aluminium tube body (Guillotine test)

60.60 Standard published

CEN/TC 261

Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance under dynamic loading

60.60 Standard published

CEN/TC 33

Natural stone test methods - Determination of sensitivity to accidental staining

60.60 Standard published

CEN/TC 246

Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance to manual burglary attempts

60.60 Standard published

CEN/TC 33

Conservation of cultural heritage - Test methods - Measurement of water absorption by pipe method

90.93 Standard confirmed

CEN/TC 346

Natural stone test methods - Determination of resistance of marble to thermal and moisture cycles

60.60 Standard published

CEN/TC 246

Textiles - Silk woven fabrics for womenswear, silk squares, scarves and ties - Requirements and test methods

90.93 Standard confirmed

CEN/TC 248

Petrol vapour recovery during refuelling of motor vehicles at service stations - Part 1: Test methods for the type approval efficiency assessment of petrol vapour recovery systems

90.93 Standard confirmed

CEN/TC 393

Petrol vapour recovery during refuelling of motor vehicles at service stations - Part 2: Test methods for verification of vapour recovery systems at service stations

90.93 Standard confirmed

CEN/TC 393

Conservation of Cultural Heritage - Test methods - Determination of drying properties

90.93 Standard confirmed

CEN/TC 346

Laminate floor coverings - Underlays - Specification, requirements and test methods

90.60 Close of review

CEN/TC 134

Fan assisted radiators, convectors and trench convectors - Part 2: Test method and rating for thermal output

90.93 Standard confirmed

CEN/TC 130

Fan assisted radiators, convectors and trench convectors - Part 3: Test method and rating for cooling capacity

90.93 Standard confirmed

CEN/TC 130

Internal blinds - Protection from strangulation hazards - Test methods

90.20 Standard under periodical review

CEN/TC 33

Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices

90.20 Standard under periodical review

CEN/TC 33

Chemical disinfectants and antiseptics - Quantitative surface test for the evaluation of bactericidal activity of chemical disinfectants and antiseptics used in veterinary area on porous surfaces without mechanical action - Test method and requirements (phase 2, step 2)

90.93 Standard confirmed

CEN/TC 216

Chemical disinfectants and antiseptics - Quantitative surface test for the evaluation of fungicidal or yeasticidal activity of chemical disinfectants and antiseptics used in the veterinary area on non-porous surfaces without mechanical action - Test method and requirements (phase 2, step 2)

90.93 Standard confirmed

CEN/TC 216

Test methods for nonwoven compresses for medical use - Part 1: Nonwovens used in the manufacture of compresses

90.93 Standard confirmed

CEN/TC 205

Test methods for nonwoven compresses for medical use - Part 2: Finished compresses

90.93 Standard confirmed

CEN/TC 205

Chimneys - Accessories - Part 1: Chimney silencers - Requirements and test methods

60.60 Standard published

CEN/TC 166

Chimneys - Accessories - Part 2: Chimney fans - Requirements and test methods

90.93 Standard confirmed

CEN/TC 166

Chimneys - Accessories - Part 3: Draught regulators, standstill opening devices and combined secondary air devices - Requirements and test methods

90.93 Standard confirmed

CEN/TC 166

Chimneys - Accessories - Part 4: Flue dampers - Requirements and test methods

60.60 Standard published

CEN/TC 166

Chimneys - Accessories - Part 6: Access components - Requirements and test methods

60.60 Standard published

CEN/TC 166

Chimneys - Accessories - Part 7: Rain caps - Requirements and test methods

90.93 Standard confirmed

CEN/TC 166

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of fungicidal or yeasticidal activity of chemical disinfectants and antiseptics used in food, industrial, domestic and institutional areas - Test method and requirements (phase 2, step 1)

90.20 Standard under periodical review

CEN/TC 216

Test method for the determination of the degree of soil acidity according to Baumann-Gully

90.93 Standard confirmed

CEN/TC 104

Residential solid fuel burning appliances - Part 1: General requirements and test methods

60.60 Standard published

CEN/TC 295

Modular mechanical locked floor coverings (MMF) - Specification, requirements and test method for multilayer modular panels for floating installation

60.60 Standard published

CEN/TC 134

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and antiseptics used in the veterinary area - Test method and requirements (phase 2, step 1)

60.60 Standard published

CEN/TC 216

Packaging - Flexible tubes - Test method to determine the orientation of the flip-top cap

60.60 Standard published

CEN/TC 261

Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of fungicidal or yeasticidal activity of chemical disinfectants and antiseptics used in the veterinary area - Test method and requirements (phase 2, step 1)

60.60 Standard published

CEN/TC 216

Playing field equipment - Portable and permanent socketed goals - Functional, safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Conservation of Cultural Heritage - Surface protection for porous inorganic materials - Laboratory test methods for the evaluation of the performance of water repellent products

90.93 Standard confirmed

CEN/TC 346

Domestic swimming pools - Part 1: General requirements including safety and test methods

60.60 Standard published

CEN/TC 402

Domestic swimming pools - Part 2: Specific requirements including safety and test methods for inground pools

90.93 Standard confirmed

CEN/TC 402

Domestic swimming pools - Part 3: Specific requirements including safety and test methods for aboveground pools

90.93 Standard confirmed

CEN/TC 402

Laboratory local exhaust devices - Part 1: General requirements and type test methods for articulated extraction arms

60.60 Standard published

CEN/TC 332

Chemical disinfectants and antiseptics - Quantitative test method for the evaluation of bactericidal and yeasticidal activity on non-porous surfaces with mechanical action employing wipes in the medical area (4- field test) - Test method and requirements (phase 2, step 2)

90.92 Standard to be revised

CEN/TC 216

Chemical disinfectants and antiseptics - Chemical-thermal textile disinfection - Test method and requirements (phase 2, step 2)

60.60 Standard published

CEN/TC 216

Permanently installed outdoor fitness equipment - Safety requirements and test methods

90.92 Standard to be revised

CEN/TC 136

Rubber or plastics-coated fabrics - Determination of stitch tear resistance (using a needle) - Test method

90.93 Standard confirmed

CEN/TC 248

Child protective products - Consumer fitted finger protection devices for doors - Safety requirements and test methods

90.93 Standard confirmed

CEN/TC 252

Playing field equipment - Lightweight goals - Functional, safety requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip

90.93 Standard confirmed

CEN/TC 132

Building hardware - Corrosion resistance - Requirements and test methods

90.93 Standard confirmed

CEN/TC 33

Building hardware - Corrosion resistance - Requirements and test methods

60.60 Standard published

CEN/TC 33

Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods

60.60 Standard published

CEN/TC 19

Domestic swimming pools - Water systems - Part 1: Filtration systems - Requirements and test methods

90.93 Standard confirmed

CEN/TC 402

Domestic swimming pools - Water systems - Part 2: Circulation systems - Requirements and test methods

90.93 Standard confirmed

CEN/TC 402

Mountaineering equipment - Avalanche airbag systems - Safety requirements and test methods

90.92 Standard to be revised

CEN/TC 136

Railway applications - Track - Noise barriers and related devices acting on airborne sound propagation - Non-acoustic performance - Part 1: Mechanical performance under static loadings - Calculation and test method

90.93 Standard confirmed

CEN/TC 256

Automotive fuels - Automotive B10 diesel fuel - Requirements and test methods

60.60 Standard published

CEN/TC 19

Emission safety of combustible air fresheners - Test methods

90.93 Standard confirmed

CEN/TC 421

Curtain walling - Determination of the strength of shear connections - Test method and requirements

60.60 Standard published

CEN/TC 33

Bio-based solvents - Requirements and test methods

90.93 Standard confirmed

CEN/TC 411

Chemical disinfectants and antiseptics - Quantitative non-porous surface test without mechanical action for the evaluation of virucidal activity of chemical disinfectants used in the medical area - Test method and requirements (phase 2/step 2)

90.60 Close of review

CEN/TC 216

Textile child care articles - Safety requirements and test methods for children's cot duvets - Part 1: Duvet (excluding duvet covers)

90.93 Standard confirmed

CEN/TC 248

Textile child care articles - Safety requirements and test methods for children's cot duvets - Part 2: Duvet covers (excluding duvet)

60.60 Standard published

CEN/TC 248

Textile child care articles - Safety requirements and test methods for children's cot bumpers

90.93 Standard confirmed

CEN/TC 248

Textile child care articles - Safety requirements and test methods for children's sleep bags for use in a cot

60.60 Standard published

CEN/TC 248

Timber structures - Test methods - Determination of the long term behaviour of coated and uncoated dowel-type fasteners

90.93 Standard confirmed

CEN/TC 124

Energy efficiency of Industrial trucks - Test methods - Part 1: General

90.60 Close of review

CEN/TC 150

Energy efficiency of Industrial trucks - Test methods - Part 2: Operator controlled self-propelled trucks, towing tractors and burden-carrier trucks

90.60 Close of review

CEN/TC 150

Energy efficiency of Industrial trucks - Test methods - Part 3: Container handling lift trucks

90.60 Close of review

CEN/TC 150

Energy efficiency of Industrial trucks - Test methods - Part 4: Variable-reach rough-terrain trucks

90.93 Standard confirmed

CEN/TC 150

Energy efficiency of Industrial trucks - Test methods - Part 6: Container straddle carrier

60.60 Standard published

CEN/TC 150

Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms

90.93 Standard confirmed

CEN/TC 155

Diving equipment - Diving open heel fins - Requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Diving equipment - Diving mask - Requirements and test methods

90.93 Standard confirmed

CEN/TC 136

Winter service equipment and products - De-icing agents - Part 1: Sodium chloride - Requirements and test methods

90.93 Standard confirmed

CEN/TC 337

Winter service equipment and products - De-icing agents - Part 2: Calcium chloride and Magnesium chloride - Requirements and test methods

90.93 Standard confirmed

CEN/TC 337

Powered industrial trucks - Visibility - Test methods and verification - Part 10: Towing and Pushing tractors and Burden carrier

60.60 Standard published

CEN/TC 150