Restriction of Hazardous Substances


Technical committee




Hazardous substance

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4: Capture efficiency of an exhaust system - Tracer method

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Separation efficiency by mass, unducted outlet

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8: Pollutant concentration parameter, test bench method

90.93 Standard confirmed

CEN/TC 114

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method

90.93 Standard confirmed

CEN/TC 114

Agricultural tractors and self-propelled sprayers - Protection of the operator (driver) against hazardous substances - Part 1: Cab classification, requirements and test procedures

60.60 Standard published

CEN/TC 144

Agricultural tractors and self-propelled sprayers - Protection of the operator (driver) against hazardous substances - Part 2: Filters, requirements and test procedures

60.60 Standard published

CEN/TC 144

Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances

60.60 Standard published

CLC/TC 111X

Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances

60.60 Standard published

CLC/TC 111X

Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1:2015)

60.60 Standard published

CEN/TC 114

Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2:2015)

60.60 Standard published

CEN/TC 114

Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances

60.60 Standard published

TC 111

Amendment 1 - Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances

60.60 Standard published

TC 111

Safety of machinery — Reduction of risks to health resulting from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Reduction of risks to health resulting from hazardous substances emitted by machinery — Part 2: Methodology leading to verification procedures

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 1: Selection of test methods

90.20 Standard under periodical review

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 3: Test bench method for the measurement of the emission rate of a given pollutant

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 4: Tracer method for the measurement of the capture efficiency of an exhaust system

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 5: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with unducted outlet

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 6: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with ducted outlet

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 7: Test bench method for the measurement of the pollutant concentration parameter

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 8: Room method for the measurement of the pollutant concentration parameter

90.93 Standard confirmed

ISO/TC 199

Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 9: Decontamination index

90.93 Standard confirmed

ISO/TC 199

Malleable cast iron fittings threaded to ISO 7-1 — Amendment 1: Chemical composition of the zinc coating — adjustment to actual requirements regarding hazardous substances

60.60 Standard published

ISO/TC 5/SC 5



Dangerous substance

Packaging - Requirements for measuring and verifying the four heavy metals and other dangerous substances present in packaging, and their release into the environment - Part 2: Requirements for measuring and verifying dangerous substances present in packaging, and their release into the environment

60.60 Standard published

CEN/TC 261

Concrete - Release of regulated dangerous substances into soil, groundwater and surface water - Test method for new or unapproved constituents of concrete and for production concretes

60.60 Standard published

CEN/TC 51

Construction products - Assessment of release of dangerous substances - Barriers to trade

60.60 Standard published

CEN/TC 351

Construction products - Assessment of the release of regulated dangerous substances from construction products based on the WT, WFT/FT procedures

60.60 Standard published

CEN/TC 351

Construction Products - Assessment of release of dangerous substances - Content of regulated dangerous substances - Selection of analytical methods

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Concept of horizontal testing procedures in support of requirements under the CPD

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Complement to sampling

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Barriers to use - Extension to CEN/TR 15855 Barriers to trade

60.60 Standard published

CEN/TC 351

Construction Products - Assessment of release of dangerous substances - Use of harmonised horizontal assessment methods

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Guidance on the statistical assessment of declared values - Part 1: Principles and rules of application

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Guidance on the statistical assessment of declared values - Part 2: Technical and statistical background

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Guidance on the use of ecotoxicity tests applied to construction products

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Radiation from construction products - Dose assessment of emitted gamma radiation

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air of ammonia from cellulose insulation at 90 % RH

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Part 1: Guidance for the determination of leaching tests and additional testing steps

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Part 3: Horizontal up-flow percolation test

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in eluates

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Digestion by aqua regia for subsequent analysis of inorganic substances

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in digests and eluates - Analysis by Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES)

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in digests and eluates - Analysis by Inductively Coupled Plasma - Mass Spectrometry (ICP-MS)

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Content of inorganic substances - Methods for analysis of aqua regia digests

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Determination of activity concentrations of radium-226, thorium-232 and potassium-40 in construction products using semiconductor gamma-ray spectrometry

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Content of organic substances - Methods for extraction and analysis

60.60 Standard published

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Analysis of organic substances in eluates

60.60 Standard published

CEN/TC 351

Packaging - Requirements for measuring and verifying the four heavy metals and other dangerous substances present in packaging and their release into the environment - Part 1: Requirements for measuring and verifying the four heavy metals present in packaging

90.93 Standard confirmed

CEN/TC 261

Construction products: Assessment of release of dangerous substances - Determination of emissions into indoor air

60.60 Standard published

CEN/TC 351

Construction products - Assessment of release of dangerous substances - Terminology

90.93 Standard confirmed

CEN/TC 351

Construction products: Assessment of release of dangerous substances - Preparation of test portions from the laboratory sample for testing of release and analysis of content

60.60 Standard published

CEN/TC 351

Glass in building - Assessment of release of dangerous substances - Determination of emissions into indoor air from glass products

60.60 Standard published

CEN/TC 129



Heavy metal

Packaging - Requirements for measuring and verifying the four heavy metals and other dangerous substances present in packaging, and their release into the environment - Part 2: Requirements for measuring and verifying dangerous substances present in packaging, and their release into the environment

60.60 Standard published

CEN/TC 261

Animal feeding stuffs: Methods of sampling and analysis - Performance criteria for single laboratory validated and ring-trial validated methods of analysis for the determination of heavy metals

90.93 Standard confirmed

CEN/TC 327

Packaging - Requirements for measuring and verifying the four heavy metals and other dangerous substances present in packaging and their release into the environment - Part 1: Requirements for measuring and verifying the four heavy metals present in packaging

90.93 Standard confirmed

CEN/TC 261

Wallcoverings in roll form - Determination of migration of heavy metals and certain other elements, of vinyl chloride monomer and of formaldehyde release

90.93 Standard confirmed

CEN/TC 99

Animal feeding stuffs: Methods of sampling and analysis - Determination of trace elements, heavy metals and other elements in feed by ICP-MS (multi-method)

60.60 Standard published

CEN/TC 327

Starch and derived products - Heavy metals content - Part 1: Determination of arsenic content by atomic absorption spectrometry (ISO 11212-1:1997)

90.93 Standard confirmed

CEN/SS C10

Starch and derived products - Heavy metals content - Part 2: Determination of mercury content by atomic absorption spectrometry (ISO 11212-2:1997)

90.93 Standard confirmed

CEN/SS C10

Starch and derived products - Heavy metals content - Part 3: Determination of lead content by atomic absorption spectrometry with electrothermal atomization (ISO 11212-3:1997)

90.93 Standard confirmed

CEN/SS C10

Starch and derived products - Heavy metals content - Part 4: Determination of cadmium content by atomic absorption spectrometry with electrothermal atomization (ISO 11212-4:1997)

90.93 Standard confirmed

CEN/SS C10

Cosmetics - Analytical methods - Measurement of traces of heavy metals in cosmetic finished products using ICP/MS technique (ISO 21392:2021, Corrected version 2021-12)

60.60 Standard published

CEN/TC 392

Photography — Photographic-grade chemicals — Test methods — Part 5: Determination of heavy metals and iron content

90.93 Standard confirmed

ISO/TC 42

Starch and derived products — Heavy metals content — Part 1: Determination of arsenic content by atomic absorption spectrometry

90.93 Standard confirmed

ISO/TC 93

Starch and derived products — Heavy metals content — Part 2: Determination of mercury content by atomic absorption spectrometry

90.93 Standard confirmed

ISO/TC 93

Starch and derived products — Heavy metals content — Part 3: Determination of lead content by atomic absorption spectrometry with electrothermal atomization

90.93 Standard confirmed

ISO/TC 93

Starch and derived products — Heavy metals content — Part 4: Determination of cadmium content by atomic absorption spectrometry with electrothermal atomization

90.93 Standard confirmed

ISO/TC 93

Starch and derived products — Heavy metals content — Part 4: Determination of cadmium content by atomic absorption spectrometry with electrothermal atomization — Technical Corrigendum 1

60.60 Standard published

ISO/TC 93

Traditional Chinese Medicine — Determination of heavy metals in herbal medicines used in Traditional Chinese Medicine

90.93 Standard confirmed

ISO/TC 249

Cosmetics — Analytical methods — Measurement of traces of heavy metals in cosmetic finished products using ICP/MS technique

60.60 Standard published

ISO/TC 217

Cosmetics — Analytical approach for screening and quantification methods for heavy metals in cosmetics

60.60 Standard published

ISO/TC 217