DISCLAMER: This is an informative page, providing added value information on standards. Information may evolve and change subject to the publication of other legislative texts. Genorma.com informs their users that users are responsible for deciding the version of the standard that is applicable to their products, and not Genorma.com. As a consequence, Genorma.com users are encouraged to check the legal text accessible through the following link: https://eur-lex.europa.eu/legal-content/EN/ALL/?uri=CELEX:32020D0542 and related pieces of legislation.
CELEX:32020D0542 (https://eur-lex.europa.eu/legal-content/EN/ALL/?uri=CELEX:32020D0542)
ELI: http://data.europa.eu/eli/dec_impl/2020/542/oj
Date of document: 16/04/2020; Date of adoption
Date of effect: 20/04/2020; Entry into force Date pub. See Art 3
Date of end of validity: No end date
EUROVOC descriptor:
marketing standard; technical specification; European standard; harmonisation of standards; product safety; safety standard; technical standard; pressure equipment; European Committee for Standardisation;
Internal market - Principles
13.30.99.00 Industrial policy and internal market / Internal market: approximation of laws / Other sectors for approximation of laws
Author: European Commission, Directorate-General for Internal Market, Industry, Entrepreneurship and SMEs
Responsible body: GROW
Form: Implementing decision
20.4.2020 | EN | Official Journal of the European Union | L 121/4
COMMISSION IMPLEMENTING DECISION (EU) 2020/542 of 16 April 2020
amending Implementing Decision (EU) 2019/1616 as regards safety devices for protection against excessive pressure, welded steel tubes for pressure purposes, unfired pressure vessels and metallic industrial piping
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EU) No 1025/2012 of the European Parliament and of the Council of 25 October 2012 on European standardisation, amending Council Directives 89/686/EEC and 93/15/EEC and Directives 94/9/EC, 94/25/EC, 95/16/EC, 97/23/EC, 98/34/EC, 2004/22/EC, 2007/23/EC, 2009/23/EC and 2009/105/EC of the European Parliament and of the Council and repealing Council Decision 87/95/EEC and Decision No 1673/2006/EC of the European Parliament and of the Council (1), and in particular Article 10(6) thereof,
Whereas:
(1) In accordance with Article 12 of Directive 2014/68/EU of the European Parliament and of the Council (2), pressure equipment or assemblies referred to in Article 4(1) and (2) of that Directive which are in conformity with harmonised standards or parts thereof, the references of which have been published in the Official Journal of the European Union, are to be presumed to be in conformity with the essential safety requirements covered by those standards or parts thereof referred to in Annex I to that Directive.
(2) By letter M/071 of 1 August 1994 the Commission made a request to the European Committee for Standardization (CEN) for drawing up, in relation to the pressure equipment, the product related standards and the standards of a horizontal nature in support of Directive 97/23/EC of the European Parliament and of the Council (3). That Directive was replaced by Directive 2014/68/EU without changing the essential safety requirements referred to in Annex I to Directive 97/23/EC.
(3) On the basis of the request M/071 CEN, in order to reflect the state of the art, amended and revised some of the existing standards. Specifically, CEN amended standards EN ISO 4126-1:2013 for safety devices for protection against excessive pressure, EN 13445-3:2014 for unfired pressure vessels, EN 13480-1:2017 and EN 13480-6:2017 for metallic industrial piping. CEN also revised the standards series EN 10217 part 1 to 6 for welded steel tubes for pressure purposes.
(4) The Commission together with the CEN has assessed whether those standards on the pressure equipment as amended or revised by CEN comply with the request M/071.
(5) The standards on the pressure equipment as amended or revised by CEN satisfy the requirements which they aim to cover and which are referred to in Annex I to Directive 2014/68/EU. It is therefore appropriate to publish the references of those standards in the Official Journal of the European Union.
(6) References of amended or revised versions of standards are to be published for the standards: EN ISO 4126-1:2013, EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002,EN 10217-6:2002/A1:2005, EN 13445-3:2014, EN 13445-3:2014/A1:2015, EN 13445-3:2014/A2:2016, EN 13445-3:2014/A3:2017, EN 13445-3:2014/A4:2018, EN 13445-3:2014/A5:2018, EN 13445-3:2014/A6:2019, EN 13480-1:2017, EN 13480-6:2017.
(7) It is therefore necessary to withdraw from the Official Journal of the European Union (4) references of the standards EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002, EN 10217-6:2002/A1:2005, EN 13480-1:2017, EN 13480-6:2017, EN ISO 4126-1:2013.
(8) In order to provide the manufacturers with sufficient time to adapt their products to the revised standards EN 10217 part 1 to 6 for welded steel tubes for pressure purposes, it is necessary to defer the withdrawal of the references to those standards.
(9) References of harmonised standards drafted in support of Directive 2014/68/EU are published in Commission Implementing Decision (EU) 2019/1616 (5). In order to ensure that the references of harmonised standards drafted in support of Directive 2014/68/EU are listed in one act, the references of standards EN ISO 4126-1:2013, EN ISO 4126-1:2013/A2:2019; EN 10217-1:2019, EN 10217-2:2019, EN 10217-3:2019, EN 10217-4:2019, EN 10217-5:2019, EN 10217-6:2019, EN 13480-1:2017, EN 13480-1:2017/A1:2019, EN 13480-6:2017, EN 13480-6:2017/A1:2019 should be included in Annex I to that Implementing Decision, and the references to standards EN 10217-1:2002, EN 10217-1:2002/A1:2005, EN 10217-2:2002, EN 10217-2:2002/A1:2005, EN 10217-3:2002, EN 10217-3:2002/A1:2005, EN 10217-4:2002, EN 10217-4:2002/A1:2005, EN 10217-5:2002, EN 10217-5:2002/A1:2005, EN 10217-6:2002, EN 10217-6:2002/A1:2005, EN 13480-1:2017, EN 13480-6:2017, EN ISO 4126-1:2013 should be included in Annex II to that Implementing Decision.
(10) The reference of standard EN 13445-3:2014 and the references of its amendments EN 13445-3:2014/A1:2015, EN 13445-3:2014/A2:2016, EN 13445-3:2014/A3:2017, 13445-3:2014/A4:2018, EN 13445-3:2014/A5:2018, EN 13445-3:2014/A6:2019 are included in Annex I to Implementing Decision (EU) 2019/1616. Further two amendments have been made to standard EN 13445-3:2014. It is appropriate to replace the relevant entry in that Annex, adding the references of amendments EN 13445-3:2014/A7:2019 and EN 13445-3:2014/A8:2019.
(11) Implementing Decision (EU) 2019/1616 should therefore be amended accordingly.
(12) Compliance with a harmonised standard confers a presumption of conformity with the corresponding essential requirements set out in Union harmonisation legislation from the date of publication of the reference of such standard in the Official Journal of the European Union. This Decision should therefore enter into force on the date of its publication,
HAS ADOPTED THIS DECISION:
Annex I to Implementing Decision (EU) 2019/1616 is amended in accordance with Annex I to this Decision.
Annex II to Implementing Decision (EU) 2019/1616 is amended in accordance with Annex II to this Decision.
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union.
Done at Brussels, 16 April 2020.
For the Commission
The President
Ursula VON DER LEYEN
(1) OJ L 316, 14.11.2012, p. 12.
(2) Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment (OJ L 189, 27.6.2014, p. 164).
(3) Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment (OJ L 181, 9.7.1997, p. 1).
(4) OJ C 326, 14.9.2018, p. 94.
(5) Commission Implementing Decision (EU) 2019/1616 of 27 September 2019 on the harmonised standards for pressure equipment drafted in support of Directive 2014/68/EU of the European Parliament and of the Council (OJ L 250, 30.9.2019, p. 95).
Annex I to Implementing Decision (EU) 2019/1616 is amended as follows:
(1) entry No 8 is replaced by the following:
‘8. | EN 13445-3:2014 | Unfired pressure vessels – Part 3: Design
| EN 13445-3:2014/A1:2015 |
| EN 13445-3:2014/A2:2016 |
| EN 13445-3:2014/A3:2017 |
| EN 13445-3:2014/A4:2018 |
| EN 13445-3:2014/A5:2018 |
| EN 13445-3:2014/A6:2019 |
| EN 13445-3:2014/A7:2019 |
| EN 13445-3:2014/A8:2019’ |
(2) the following entries are added:
No | Reference of the standard | Title of the standard
‘15. | EN ISO 4126-1:2013 | Safety devices for protection against excessive pressure – Part 1: Safety valves (ISO 4126-1:2013)
| EN ISO 4126-1:2013/A2:2019 |
| EN 10217-1:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
| EN 10217-2:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties
| EN 10217-3:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 3: Electric welded and submerged arc welded alloy fine grain steel tubes with specified room, elevated and low temperature properties
| EN 10217-4:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 4: Electric welded non-alloy steel tubes with specified low temperature properties
| EN 10217-5:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties
| EN 10217-6:2019 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties
| EN 13480-1:2017 | Metallic industrial piping – Part 1: General
| EN 13480-1:2017/A1:2019 |
| EN 13480-6:2017 | Metallic industrial piping – Part 6: Additional requirements for buried piping
| EN 13480-6:2017/A1:2019’ |.
In Annex II to Implementing Decision (EU) 2019/1616 the following entries are added:
No | Reference of the standard | Title of the standard | Date of withdrawal
‘13. | EN 10217-1:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties | 20 April 2021
| EN 10217-1:2002/A1:2005 | | 20 April 2021
| EN 10217-2:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties | 20 April 2021
| EN 10217-2:2002/A1:2005 | | 20 April 2021
| EN 10217-3:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 3: Alloy fine grain steel tubes | 20 April 2021
| EN 10217-3:2002/A1:2005 | | 20 April 2021
| EN 10217-4:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 4: Electric welded non-alloy steel tubes with specified low temperature properties |
| EN 10217-4:2002/A1:2005 | | 20 April 2021
| EN 10217-5:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties | 20 April 2021
| EN 10217-5:2002/A1:2005 | | 20 April 2021
| EN 10217-6:2002 | Welded steel tubes for pressure purposes – Technical delivery conditions – Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties | 20 April 2021
| EN 10217-6:2002/A1:2005 | | 20 April 2021
| EN 13480-1:2017 | Metallic industrial piping – Part 1: General | 20 April 2020
| EN 13480-6:2017 | Metallic industrial piping – Part 6: Additional requirements for buried piping | 20 April 2020
| EN ISO 4126-1:2013 | Safety devices for protection against excessive pressure – Part 1: Safety valves (ISO 4126-1:2013) | 20 April 2020’
See below to obtain the cited standards or to obtain information about them:
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
90.60 Close of review
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties
90.60 Close of review
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Electric welded and submerged arc welded alloy fine grain steel tubes with specified room, elevated and low temperature properties
90.60 Close of review
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 4: Electric welded non-alloy steel tubes with specified low temperature properties
90.60 Close of review
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties
90.60 Close of review
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties
90.60 Close of review
Metallic industrial piping - Part 6: Additional requirements for buried piping
99.60 Withdrawal effective
Metallic industrial piping - Part 6: Additional requirements for buried piping
99.60 Withdrawal effective
Safety devices for protection against excessive pressure - Part 1: Safety valves (ISO 4126-1:2013)
60.60 Standard published
Safety devices for protection against excessive pressure - Part 1: Safety valves (ISO 4126-1:2013)
60.60 Standard published
